Connector End View (C218A) - CLOCKSPRING

2021 Ford Edge SE, 4WDSECTION Connector End View (C218A) - CLOCKSPRING
WARNING: This page is about a different car, the 2019 Ford F-550 Super Duty, 2019 Ford F-450 Super Duty, 2019 Ford F-350 Super Duty, and 2019 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
Connector: Description Color Harness Base Part # Service Pigtail
C218A CLOCKSPRING 14401 part# N/A See Below
GFDWR56267Courtesy of FORD MOTOR COMPANY
Terminal Part Number  Service Part Number  Size 
3F2T-14474-SA|1L2T-14474-CA Not Available
3F2T-14474-SA DU2Z-14474-BA 0.64
3F2T-14474-RA DU2Z-14474-BA 0.64
1L2T-14474-CA DU2Z-14474-BA 0.64
Pin  Circuit  Gauge  Circuit Function  Qualifier  Terminal Part Number 
1 * * Not Used N/A
2 RHS81 (VT-WH) 22 THERMISTOR - HEATED STEERING WHEEL - 3F2T-14474-SA
3 VHS81 (GN-WH) 22 THERMISTOR - HEATED STEERING WHEEL + 3F2T-14474-SA
4 VLN04 (VT-GY) 22 CTRL MOD. - IP/SWITCH ILLUMINATION 3F2T-14474-SA
5 CRH04 (VT-GN) 22 CTRL MOD. - RELAY HORN 3F2T-14474-SA|1L2T-14474-CA
5 CR101 (VT-BN) 18 CTRL MOD. - AIR BAG DRIVER 1 + 3F2T-14474-SA|1L2T-14474-CA
6 GD215 (BK-VT) 22 GROUND - INSTRUMENT PANEL STRUCTURE # 2ND POINT 3F2T-14474-SA
7 * * Not Used N/A
8 GD215 (BK-GY) 18 GROUND - INSTRUMENT PANEL STRUCTURE # 2ND POINT 3F2T-14474-RA
8 GD215 (BK-GN) 18 GROUND - INSTRUMENT PANEL STRUCTURE # 2ND POINT 3F2T-14474-RA
9 VLN04 (VT-GY) 22 CTRL MOD. - IP/SWITCH ILLUMINATION 3F2T-14474-SA
10 * * Not Used N/A
11 CR101 (VT-BN) 18 CTRL MOD. - AIR BAG DRIVER 1 + 1L2T-14474-CA
11 RR101 (YE-GN) 18 CTRL MOD. - AIR BAG DRIVER 1 - 1L2T-14474-CA
12 RR101 (YE-GN) 18 CTRL MOD. - AIR BAG DRIVER 1 - 1L2T-14474-CA

Available Pigtail Kits 

Pigtail Kit Part Number WPT-949

GFDWR702Courtesy of FORD MOTOR COMPANY

Service Part Number:

3U2Z-14S411-BMAB 

Gauge:

18 

Pin material:

Silver 

Cavities:

12 

Vehicle Uses:

  • Control - Navigation Display
  • Module - Driver Door
  • Module - Front Interface
  • Monitor - Video/DVD
  • Switch - Gear Shift Select/Neutral Safety
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.