SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2021EDGE SE, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 13 (ENGINE CONTROLS - PINPOINT TESTS (DIESEL))PINPOINT TESTS ZZ: INTERMITTENTINTRODUCTION
2021 Ford Edge SE, 4WD

Pinpoint Tests ZZ: Intermittent: Introduction

2021 Ford Edge SE, 4WDSECTION Introduction
WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2018 Ford Transit-350 HD, 2018 Ford Transit-350, 2018 Ford Transit-250, 2018 Ford Transit-150, and 2018 Ford F-550 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

This pinpoint test is intended to diagnose and isolate intermittent concerns for all electronic engine control (EEC) subsystems.

This chart is used to determine which test to run for the suspect circuit. Parameter identifiers (PIDs) corresponding to each circuit are listed. Some circuits do not have an associated PID or the PID may not be available and has to be measured with a digital multimeter (DMM). More specific information on the PID can be found in REFERENCE VALUES .

PCM PIDS/SIGNALS

PCM/PIDS/SIGNALS Associated Circuit Test Type
AAT, AAT_V AAT Input
BOO1 BPP Input
BOO2 BPS Input
CAC_T, CAC_V, CACT_V CACT Input
CC_VENTHOSE_V CRNKCSVT Input
DPF_INP, DPF_INP_V DPF12 Input
DPF_V DPF11 Input
EBP, EBP_V EBP Input
ECT, ECT1_V ECT Input
ECT2, ECT2_V ECT2 Input
EGRCBV EGRCBV Output
EGRCIT_V, EGRTA EGRT11 Input
EGRCOT_V, EGRTC EGRT12 Input
EGRTP_V TP#2 Output
EGRVP EGR Input
EGT11, EGT11_V EGT11 Input
EGT12, EGT12_V EGT12 Input
EGT13, EGT13_V EGT13 Input
EGT14, EGT14_V EGT14 Input
EOT, EOT_V EOT Input
EXHAUST_BRK EBIS Input
F_PCV FPCV Output
F_VCV FVCV or FVR Output
FANSS FSS Input
FLI FLI Input
FLP FLP Input
FP FPC Output
FPM FPM#EFPR Input
FRP FRP Input
FRT, FRT_V FRT Input
IAT11, IAT11_V IAT Input
LP_FUEL_SW FDPS Input
MAF, MAF_HZ MAF Input
MAP, MAP_V MAP Input
NOX11 CAN Input
OSS_SRC OSS Input
PTO_STATUS PTO Input
REDUCT_PRES_V RDP Input
REDUCT_RV_DC RDPGC Output
REDUCT_TNK_LV RDL1, RDL2, RDL3 Input
REDUCT_TNK_P RDP Input
REDUCT_TNK_T RDT Input
TCBP_V TCBP Input
TURBO_WGATE TCWRVS Output
VGT_POS_V VGTP Input
Use DMM VPWR Input
Use DMM VREF Output
WFS, WFS_V WIF Input
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.