SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSFORD2019EXPLORER LIMITED, 3.5L ENG VIN 8, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOMMUNICATION DEVICESMODULE CONFIGURATIONDESCRIPTION AND OPERATIONMODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTIONMODULE CONFIGURATION AND PARAMETER CHART
2019 Ford Explorer Limited, 3.5L Eng VIN 8, AWD

Module Configuration and Parameter Chart

2019 Ford Explorer Limited, 3.5L Eng VIN 8, AWDSECTION Module Configuration and Parameter Chart

The chart describes specific module configuration information:

Module Name Module Address Programmable Module Installation (PMI) Available Reprogram/Flash Capable Requires Adaptive Learning or Calibration Available Progammable Parameters
APIM 7D0 Yes Yes No None
ATCM 792 No Yes No None
ABS module 760 Yes Yes IVD initialization Tire size
ACM 727 Yes Yes No Mute radio enable configuration
BECMB 723 Yes Yes No None
BCM 726 Yes Yes Ambient lighting calibration
Rear view camera calibration		 Auto unlock 1-4 enable/disable
DRL feature
Frequency selection
Headlamp type
Perimeter alarm
Police dark car, silent mode feature
Remote keyless entry enable/disable
Remote start enable
Remote start lighting enable
Tire pressure
Tire size
Trim switch inhibit
CCM 764 Yes Yes Radar horizontal and vertical alignment calibration None
DSP 783 Yes Yes No None
DACMC (integrated with ACM) 7D5 Yes Yes No None
DDM 740 Yes Yes No None
DSM 744 Yes Yes No None
FCDIM 7A5 Yes Yes No None
FCIMB 7A0 No Yes No None
GWM 716 Yes Yes No None
GFM (SWIM) 7A1 No Yes No None
GPSM 701 Yes Yes No None
HCM 734 Yes Yes LED Lamp Driver Module Initialization None
HUD module 7B2 No Yes No None
HSWM 714 Yes Yes No None
HVAC module 733 Yes Yes No None
IPC 720 Yes Yes No Driver Beltminder®
Courtesy wipe after wash
Gallon display type
Passenger Beltminder®
Police max speed selection (only configurable with speed limiter function)
Rear reverse gear wipe
Remote start feature enable
Remote start climate settings
Driver seat
Passenger seat
Rear defrost
Steering wheel
IPMA 706 Yes Yes Camera calibration None
IPMB 7B1 Yes Yes Camera calibration None
OCS module 765 No Yes OCS re-zero None
PAM (integrated with BCM) 736 Yes Yes No None
PSCM 730 Yes Yes No None
PCM 7E0 Yes Yes Misfire Monitor Neutral Profile Correction procedure None
PDM 741 Yes Yes No None
RTM 751 Yes Yes No None
RGTM 775 No Yes No None
RHVAC module 785 No Yes No None
RCM 737 Yes Yes No Driver Beltminder®
Passenger Beltminder®
SCMG 712 Yes Yes No None
SCME 776 Yes Yes No None
SCMH 713 Yes Yes No None
SODL 7C4 Yes Yes No BLIS/ CTA enable/disable
SODR 7C6 Yes Yes No BLIS/ CTA enable/disable
SCCM 724 Yes Yes No None
TCU 754 Yes Yes No None
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.