Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2018F-450 SUPER DUTY LARIAT, 4D PICKUP CREW CAB, 4WDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX (MODULE COMMUNICATIONS - WIPER & WASHER SYSTEM)PARKING AID SYSTEM (WITH: PARKING AID CAMERA) DTCSIPMB - 2 CAMERA SYSTEM
2018 Ford F-450 Super Duty Lariat, 4D Pickup Crew Cab, 4WD
IPMB - 2 Camera System
2018 Ford F-450 Super Duty Lariat, 4D Pickup Crew Cab, 4WDSECTION IPMB - 2 Camera System
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B115E:08 | Camera Module: Bus Signal/Message Failure | GO to Pinpoint Test E |
| B115E:49 | Camera Module: Internal Electronic Failure | Sets in continuous memory and on-demand in the IPMB when an internal fault is detected in the rear parking aid camera. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMB self-test. If DTC B115E:49 returns, INSTALL a new rear parking aid camera. Refer to: Rear Parking Aid Camera . |
| B115E:55 | Camera Module: Not Configured |
NOTE:
A LIN circuit fault may prevent the front or rear parking aid camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern. Sets in continuous memory and on-demand in the IPMB when the rear parking aid camera is not configured.VERIFY the battery voltage and condition.PERFORM the rear parking aid camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization. |
| B148E:08 | Front Camera: Bus Signal/Message Failure | GO to Pinpoint Test F |
| B148E:49 | Front Camera: Internal Electronic Failure | Sets in continuous memory and on-demand in the IPMB when an internal fault is detected in the CHMSL parking aid camera. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMB self-test. If DTC B148E:49 returns, INSTALL a new CHMSL parking aid camera. Refer to: High Mounted Stoplamp . |
| B148E:55 | Front Camera: Not Configured |
NOTE:
A LIN circuit fault may prevent the front or rear parking aid camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern. Sets in continuous memory and on-demand in the IPMB when the CHMSL camera is not configured.VERIFY the battery voltage and condition.PERFORM the front camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization. |
| B14A5:11 | Multi-Camera View Switch: Circuit Short To Ground | GO to Pinpoint Test R |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to Pinpoint Test S |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the ABS module. See the ABS module DTC Chart. Refer to: Anti-Lock Brake System (ABS) and Stability Control
. If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U201A:55 | Control Module Main Calibration Data: Not Configured | VERIFY the battery voltage and condition. CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. Refer to: Image Processing Module B (IPMB) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | VERIFY the battery voltage and condition. CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. Refer to: Image Processing Module B (IPMB) . |
| U3000:42 | Control Module: General Memory Failure | RETRIEVE and REPAIR all other IPMB Diagnostic Trouble Codes (DTCS) and TEST the system for normal operation. If DTC U3000:42 is still present after all other Diagnostic Trouble Codes (DTCs) have been repaired, INSTALL a new IPMB. Refer to: Image Processing Module B (IPMB) . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.