Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2018F-150 XLT, 4D PICKUP EXTRA CAB, 3.5L ENG VIN G, RWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX - (ANTI LOCK BRAKE SYSTEM - ELECTRONIC ENGINE CONTROLS)AUTOMATIC TRANSMISSION 6R80 DTCS3.3L DURATEC - V6
2018 Ford F-150 XLT, 4D Pickup Extra Cab, 3.5L Eng VIN G, RWD
3.3L Duratec - V6
2018 Ford F-150 XLT, 4D Pickup Extra Cab, 3.5L Eng VIN G, RWDSECTION 3.3L Duratec - V6
DTC INDEX
| DTC | Description | Component | Action |
|---|---|---|---|
| P0218 | Transmission Fluid Temperature Sensor "A" Over Temperature Condition Engine | Transmission over temperature |
NOTE:
P0218 causes the powertrain to limit torque to prevent transmission overheating. The DTC P0218 may set in conjunction with DTC P1783. CLEAR the DTC. If DTC P0218 returns, determine if this DTC was set in conjunction with any transmission fluid temperature sensor circuit DTCs and RESOLVE them first, otherwise, Refer to: Transmission Cooling
. |
| P0657 | Actuator Supply Voltage A Circuit Open | Actuator Supply Voltage A Circuit Open | Power is routed through the Transmission Solenoid Power Control (TSPC) relay (inside the PCM) to all solenoids. If the power circuit to the transmission solenoids or the TSPC relay fails open, then all solenoids are failed electrically off. CHECK for open, short to ground or the transmission connector disconnected. The TSPC relay also disables power to the transmission solenoids when certain transmission DTCs are set. REPAIR as required. CLEAR the DTC. GO to Pinpoint Test A |
| P0701 | Transmission Control System Range/Performance | Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(es)). | Intermittent clutch on fault and may set with DTCs P2700, P2701, P2702, P2703 and/or P2704. CLEAR the DTC. If DTC P0701 returns, Refer to: Diagnosis By Symptom . |
| P0702 | Transmission Control System Electrical | Battery | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and (KOER self-test. If DTC P0702 returns, Refer to: Charging System - 3.3L Duratec - V6/5.0L 32V Ti-VCT . |
| P0705 | Transmission Range Sensor "A" Circuit (PRNDL Input) | TR sensor | GO to Pinpoint Test C |
| P0706 | Transmission Range Sensor "A" Circuit Range/Performance | TR sensor | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is greater or less than the expected duty cycle by 50Hz or more. Engine may not crank. CLEAR the DTC. If DTC P0706 returns, GO to Pinpoint Test C |
| P0707 | Transmission Range Sensor "A" Circuit Low | TR sensor | Engine may not crank, CLEAR the DTC. If DTC P0707 returns, GO to Pinpoint Test C |
| P0708 | Transmission Range Sensor "A" Circuit High | TR sensor | Engine may not crank, CLEAR the DTC. If DTC P0708 returns, GO to Pinpoint Test C |
| P0709 | Transmission Range Sensor "A" Circuit Intermittent | TR sensor | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is within range but is in the dead band between the design position, and a in-range but invalid duty cycle. GO to Pinpoint Test C |
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit | TFT sensor | CLEAR the DTC. If DTC P0710 returns, GO to Pinpoint Test B |
| P0711 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance | TFT sensor | CLEAR the DTC. If DTC P0711 returns, GO to Pinpoint Test B |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low | TFT sensor | DTC P0710 may set. CLEAR the DTC. If DTC P0712 returns, GO to Pinpoint Test B |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High | TFT sensor | DTC P0710 may set. CLEAR the DTC. If DTC P0713 returns, GO to Pinpoint Test B |
| P0715 | Turbine/Input Shaft Speed Sensor "A" Circuit | TSS sensor | DTC P0717 may set. CLEAR the DTC. If DTC P0715 returns, GO to Pinpoint Test D |
| P0717 | Turbine/Input Shaft Speed Sensor "A" Circuit No Signal | TSS sensor | This DTC sets when DTC P0715 is set. REFER to DTC P0715. |
| P0718 | Turbine/Input Shaft Speed Sensor "A" Circuit Intermittent | TSS sensor | CLEAR the DTC. If DTC P0718 returns, GO to Pinpoint Test D |
| P0720 | Output Shaft Speed Sensor Circuit | OSS sensor | DTC P0722 may set. CLEAR the DTC. If DTC P0720 returns, GO to Pinpoint Test E |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | OSS sensor | CLEAR the DTC. If DTC P0721 returns, GO to Pinpoint Test E |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | OSS sensor | This DTC sets when DTC P0720 is set. REFER to DTC P0720. |
| P0729 | Gear 6 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0729 returns, Refer to: Diagnosis By Symptom . |
| P0731 | Gear 1 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0731 returns, Refer to: Diagnosis By Symptom . |
| P0732 | Gear 2 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0732 returns, Refer to: Diagnosis By Symptom . |
| P0733 | Gear 3 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0733 returns, Refer to: Diagnosis By Symptom . |
| P0734 | Gear 4 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0734 returns, Refer to: Diagnosis By Symptom . |
| P0735 | Gear 5 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0735 returns, Refer to: Diagnosis By Symptom . |
| P0740 | Torque Converter Clutch Solenoid Circuit/Open | TCC solenoid | DTC P0743 may set, CLEAR the DTC. If DTC P0740 returns, GO to Pinpoint Test A |
| P0741 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off | TCC solenoid | DTC P0741 is a non-electrical DTC. CLEAR the DTC. If DTC P0741 returns, Refer to: Diagnosis By Symptom . |
| P0742 | Torque Converter Clutch Solenoid Circuit Stuck On | TCC solenoid | DTC P0743 may set, CLEAR the DTC. If DTC P0742 returns, GO to Pinpoint Test A |
| P0743 | Torque Converter Clutch Solenoid Circuit Electrical | TCC solenoid | DTC P0740, P0742 and/or P0744 may set, CLEAR the DTC. If DTC P0743 returns, GO to Pinpoint Test A |
| P0744 | Torque Converter Clutch Solenoid Circuit Intermittent | TCC solenoid | DTC P0743 may set, CLEAR the DTC. If DTC P0744 returns, GO to Pinpoint Test A |
| P0748 | Pressure Control Solenoid "A" Electrical | LPC | DTC P0960, P0962 and/or P0963 may set, CLEAR the DTC. If DTC P0748 returns, GO to Pinpoint Test A |
| P0750 | Shift Solenoid "A" | SSA | DTC P0751 may set, CLEAR the DTC. If DTC P0750 returns, GO to Pinpoint Test A |
| P0751 | Shift Solenoid "A" Performance/Stuck Off | SSA | DTC P2700 may set, CLEAR the DTC. If DTC P0751 returns, Refer to: Diagnosis By Symptom . |
| P0752 | Shift Solenoid "A" Stuck On | SSA | CLEAR the DTC. If DTC P0752 returns, Refer to: Diagnosis By Symptom . |
| P0753 | Shift Solenoid "A" Electrical | SSA | DTC P0750, P0973 and/or P0974 may set, CLEAR the DTC. If DTC P0753 returns, GO to Pinpoint Test A |
| P0754 | Shift Solenoid "A" Intermittent | SSA | CLEAR the DTC. If DTC P0754 returns, GO to Pinpoint Test A |
| P0755 | Shift Solenoid "B" | SSB | DTC P0756 may set, CLEAR the DTC. If DTC P0755 returns, GO to Pinpoint Test A |
| P0756 | Shift Solenoid "B" Performance/Stuck Off | SSB | DTC P2701 may set, CLEAR the DTC. If DTC P0756 returns, Refer to: Diagnosis By Symptom . |
| P0757 | Shift Solenoid "B" Stuck On | SSB | DTC P2701 may set, CLEAR the DTC. If DTC P0757 returns, Refer to: Diagnosis By Symptom . |
| P0758 | Shift Solenoid "B" Electrical | SSB | DTC P0755, P0976 and/or P0977 may set, CLEAR the DTC. If DTC P0758 returns, GO to Pinpoint Test A |
| P0759 | Shift Solenoid "B" Intermittent | SSB | CLEAR the DTC. If DTC P0759 returns, GO to Pinpoint Test A |
| P0760 | Shift Solenoid "C" | SSC | DTC P0761 may set, CLEAR the DTC. If DTC P0760 returns, GO to Pinpoint Test A |
| P0761 | Shift Solenoid "C" Performance/Stuck Off | SSC | DTC P2702 may set, CLEAR the DTC. If DTC P0761 returns, Refer to: Diagnosis By Symptom . |
| P0762 | Shift Solenoid "C" Stuck On | SSC | DTC P0763 may set, CLEAR the DTC. If DTC P0762 returns, Refer to: Diagnosis By Symptom . |
| P0763 | Shift Solenoid "C" Electrical | SSC | DTC P0760, P0979 and/or P0980 may set, CLEAR the DTC. If DTC P0763 returns, GO to Pinpoint Test A |
| P0764 | Shift Solenoid "C" Intermittent | SSC | CLEAR the DTC. If DTC P0764 returns, GO to Pinpoint Test A |
| P0765 | Shift Solenoid "D" | SSD | DTC P0766 may set, CLEAR the DTC. If DTC P0765 returns, GO to Pinpoint Test A |
| P0766 | Shift Solenoid "D" Performance/Stuck Off | SSD | DTC P2704 may set, CLEAR the DTC. If DTC P0766 returns, Refer to: Diagnosis By Symptom . |
| P0767 | Shift Solenoid "D" Stuck On | SSD | DTC P07A9 and/or P2704 may set, CLEAR the DTC. If DTC P0767 returns, Refer to: Diagnosis By Symptom . |
| P0768 | Shift Solenoid "D" Electrical | SSD | DTC P0765, P0982 and/or P0983 may set, CLEAR the DTC. If DTC P0768 returns, GO to Pinpoint Test A |
| P0769 | Shift Solenoid "D" Intermittent | SSD | CLEAR the DTC. If DTC P0769 returns, GO to Pinpoint Test A |
| P0770 | Shift Solenoid "E" | SSE | DTC P0773 may set, CLEAR the DTC. If DTC P0770 returns, GO to Pinpoint Test A |
| P0771 | Shift Solenoid "E" Performance/Stuck Off | SSE | DTC P0984 may set, CLEAR the DTC. If DTC P0771 returns, Refer to: Diagnosis By Symptom . |
| P0772 | Shift Solenoid "E" Stuck On | SSE | DTC P0984 may set, CLEAR the DTC. If DTC P0772 returns, Refer to: Diagnosis By Symptom . |
| P0773 | Shift Solenoid "E" Electrical | SSE | REFER to DTC P0770. |
| P0774 | Shift Solenoid "E" Intermittent | SSE | CLEAR the DTC. If DTC P0774 returns, GO to Pinpoint Test A |
| P07A8 | Transmission Friction Element "D" Stuck Off | Transmission | CLEAR the DTC. If DTC P07A8 returns, Refer to: Diagnosis By Symptom . |
| P07A9 | Transmission Friction Element "D" Stuck On | Transmission | DTC P0767 may set, CLEAR the DTC. If DTC P07A9 returns, Refer to: Diagnosis By Symptom . |
| P07AA | Transmission Friction Element "E" Stuck Off | Transmission | CLEAR the DTC. If DTC P07AA returns, Refer to: Diagnosis By Symptom . |
| P0815 | Upshift Switch Circuit | SelectShift™ switch | CLEAR the DTC. If DTC P0815 returns, Refer to: External Controls . |
| P0816 | Downshift Switch Circuit | SelectShift™ switch | CLEAR the DTC. If DTC P0816 returns, Refer to: External Controls . |
| P0826 | Up and Down switch circuit | SelectShift™ switch | REFER to: External Controls . |
| P0882 | PCM Power Input Signal Low | Battery | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If DTC P0882 returns, Refer to: Charging System - 3.3L Duratec - V6/5.0L 32V Ti-VCT . |
| P0883 | PCM Power Input Signal High | Battery | CLEAR the DTC. If DTC P0883 returns, Refer to: Charging System - 3.3L Duratec - V6/5.0L 32V Ti-VCT . |
| P0960 | Pressure Control Solenoid Control Circuit/Open | LPC | DTC P0748 may set, CLEAR the DTC. If DTC P0960 returns, GO to Pinpoint Test A |
| P0961 | Pressure Control Solenoid Control Circuit Range/Performance | LPC | CLEAR the DTC. If DTC P0961 returns, GO to Pinpoint Test A |
| P0962 | Pressure Control Solenoid Control Circuit Low | LPC | DTC P0748 may set, CLEAR the DTC. If DTC P0962 returns, GO to Pinpoint Test A |
| P0963 | Pressure Control Solenoid Control Circuit High | LPC | DTC P0748 may set, CLEAR the DTC. If DTC P0963 returns, GO to Pinpoint Test A |
| P0973 | Shift Solenoid "A" Control Circuit Low | SSA | DTC P0753 may set, CLEAR the DTC. If DTC P0973 returns, GO to Pinpoint Test A |
| P0974 | Shift Solenoid "A" Control Circuit High | SSA | DTC P0748 may set, CLEAR the DTC. If DTC P0974 returns, GO to Pinpoint Test A |
| P0976 | Shift Solenoid "B" Control Circuit Low | SSB | DTC P0758 may set, CLEAR the DTC. If DTC P0976 returns, GO to Pinpoint Test A |
| P0977 | Shift Solenoid "B" Control Circuit High | SSB | DTC P0758 may set, CLEAR the DTC. If DTC P0977 returns, GO to Pinpoint Test A |
| P0979 | Shift Solenoid "C" Control Circuit Low | SSC | DTC P0763 may set, CLEAR the DTC. If DTC P0979 returns, GO to Pinpoint Test A |
| P0980 | Shift Solenoid "C" Control Circuit High | SSC | DTC P0763 may set, CLEAR the DTC. If DTC P0980 returns, GO to Pinpoint Test A |
| P0982 | Shift Solenoid "D" Control Circuit Low | SSD | DTC P0768 may set, CLEAR the DTC. If DTC P0982 returns, GO to Pinpoint Test A |
| P0983 | Shift Solenoid "D" Control Circuit High | SSD | DTC P0768 may set, CLEAR the DTC. If DTC P0983 returns, GO to Pinpoint Test A |
| P0984 | Shift Solenoid "E" Range/Performance | SSE | DTC P0771 and/or P0772 may set, CLEAR the DTC. If DTC P0984 returns, Refer to: Diagnosis By Symptom . |
| P0B0D | Electric/Auxiliary Transmission Fluid Pump Motor Control Module | Electric transmission fluid pump motor | CLEAR the DTC. If the DTC returns, INSTALL a new transmission fluid auxiliary pump. Refer to: Transmission Fluid Auxiliary Pump . |
| P0C27 | Electric Transmission Fluid Pump Motor Current Low | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects low current (10% to 15% duty cycle). Auto-Start-Stop unavailable and the engine will only stop when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G |
| P0C28 | Electric Transmission Fluid Pump Motor Current Low | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects low current (20% to 25% duty cycle). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G |
| P0C29 | Electric Transmission Fluid Pump Motor Current High | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects high current (20% to 25% duty cycle). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G |
| P0C2A | Electric Transmission Fluid Pump Motor Stalled | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM commands the electric transmission fluid pump on and does not detect the corresponding increase in pressure indicating a stalled pump motor. Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F |
| P0C2C | Electric Transmission Fluid Pump Control Module Feedback Signal Range/Performance | Electric transmission fluid pump motor module | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects a duty cycle that does not match a defined duty cycle range. Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F |
| P0C2D | Electric Transmission Fluid Pump Control Module Feedback Signal Low | Electric transmission fluid pump motor module | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects a duty cycle that is out of range low (less than 10%). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F |
| P0C2E | Electric Transmission Fluid Pump Control Module Feedback Signal High | Electric transmission fluid pump motor module | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects a duty cycle that is out of range high (greater than 90%). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F |
| P1001 | The KOER Not Able to Complete, KOER Aborted | PCM | RETRIEVE and RECORD all DTCs. REPAIR any self-test or CMDTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the PCM to the latest software. RERUN the KOER self-test. If the DTC returns, Refer to: PCM Hardware Testing . |
| P1397 | System Voltage Out Of Self Test Range | PCM | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RUN the KOEO self-test. If DTC P1397 returns, Refer to: Charging System - 3.3L Duratec - V6/5.0L 32V Ti-VCT . |
| P1501 | Vehicle Speed Sensor Out Of Self Test Range | PCM | Vehicle speed not at 0.0mph (km/h) during the KOEO and/or KOER self-test. CLEAR the DTC and RERUN the KOEO and KOER self-test. If DTC P1501 returns, Refer to: Anti-Lock Brake System (ABS) and Stability Control . |
| P1502 | Vehicle Speed Sensor Intermittent | PCM | Vehicle speed not at 0.0mph (km/h) during the KOEO and/or KOER self-test. CLEAR the DTC and RERUN the KOEO and KOER self-test. If DTC P1501 returns, Refer to: Anti-Lock Brake System (ABS) and Stability Control . |
| P1635 | Tire/Axle Out Of Acceptable Range | PCM | Refer to REFER to Engine Controls - Introduction (Except Diesel & Hybrid) or Engine Controls - Introduction (Diesel) . |
| P1636 | Inductive Signature Chip Communication Error | PCM | CLEAR the DTC. If DTC P1636 returns, Refer to: PCM Hardware Testing . |
| P163E | Transmission Control Module Programming Error | PCM | CLEAR the DTC. REPROGRAM the original PCM with the latest software. If DTC P163E returns, Refer to: PCM Hardware Testing . |
| P163F | Transmission ID Block Corrupted, Not Programmed | PCM | CLEAR the DTC. REPROGRAM the original PCM with the latest software. If DTC P163F returns, Refer to: PCM Hardware Testing . |
| P1700 | Transmission Intermittent Failure (failed to neutral) | Transmission | DTC P1700 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, Refer to: Diagnosis By Symptom . |
| P1702 | Transmission Range Sensor Circuit Intermittent | TR sensor | DTC P0706, P0707 and/or P0708 may set, CLEAR the DTC. If DTC P1702 returns, GO to Pinpoint Test C |
| P1705 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test | TR sensor | CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1705 returns, GO to Pinpoint Test C |
| P1711 | Transmission Fluid Temperature Sensor Out Of Self Test Range | TFT sensor | CLEAR the DTC and RERUN the KOEO and KOER self-test. |
| P1744 | Torque Converter Clutch Solenoid Circuit Performance | TCC | DTC P1744 is a non-electrical DTC. CLEAR the DTC. If DTC P1744 returns, Refer to: Diagnosis By Symptom . |
| P175A | Transmission Fluid Over Temperature Condition - Electric Transmission Fluid Pump Disabled | Transmission fluid over temperature | GO to Pinpoint Test G |
| P177F | Unable To Fully Engage Neutral | Direct or forward clutch pack | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Refer to: Transmission . |
| P1780 | Transmission Control Switch (O/D Cancel) Circuit Out of Self-Test Range | TCS | CLEAR the DTC. If DTC P1780 returns, Refer to: External Controls . |
| P1783 | Transmission Over Temperature Condition | Transmission | CLEAR the DTC. If DTC P1783 returns, determine if this DTC was set in conjunction with any transmission fluid temperature sensor circuit DTCs and RESOLVE them first, otherwise REFER to: Transmission Cooling . |
| P1910 | Reverse Lamp Control Circuit/Open | Reverse lamps | CLEAR the DTC. TEST system for normal operation. If DTC P1910 returns, Refer to: Reversing Lamps . |
| P1921 | Transmission Range Signal | TR sensor | The engine may not crank. DTC P0706, P0707 and/or P0708 may set. CLEAR the DTC. If DTC P1921 returns, CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1921 returns, GO to Pinpoint Test C |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Transmission | DTC P2700 is a non-electrical DTC. DTC P0751 and/or P0752 may set. CLEAR the DTC. If DTC P2700 returns, Refer to: Diagnosis By Symptom . |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Transmission | DTC P2701 is a non-electrical DTC. DTC P0756 and/or P0757 may set. CLEAR the DTC. If DTC P2701 returns, Refer to: Diagnosis By Symptom . |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Transmission | DTC P2702 is a non-electrical DTC. DTC P0761 and/or P0762 may set. CLEAR the DTC. If DTC P2702 returns, Refer to: Diagnosis By Symptom . |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Transmission | DTC P2703 is a non-electrical DTC. DTC P0766 and/or P0768 may set. CLEAR the DTC. If DTC P2703 returns, Refer to: Diagnosis By Symptom . |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | Transmission | DTC P2704 is a non-electrical DTC. DTC P0771 and/or P0772 may set. CLEAR the DTC. If DTC P2704 returns, Refer to: Diagnosis By Symptom . |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | Mechanical one-way clutch | DTC P2705 is a non-electrical DTC. CLEAR the DTC. If DTC P2705 returns, Refer to: Diagnosis By Symptom . |
| P2758 | Torque Converter Clutch Pressure Control Solenoid Stuck On | TCC | CLEAR the DTC. If DTC P2758 returns, Refer to: Diagnosis By Symptom . |
| P2760 | Torque Converter Clutch Pressure Control Solenoid Intermittent | TCC | CLEAR the DTC. If DTC P2760 returns, GO to Pinpoint Test A |
| P2796 | Electric Transmission Fluid Pump Control Circuit | Electric transmission fluid pump control circuit | This DTC applies to auto-start-stop vehicles only. This DTC sets when the e-pump reports to the PCM that it is not receiving a PWM from the PCM. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.