Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Connector End View (C1168) - INLINE
| Inline: | Description | Color | Harness | Base Part # | Service Pigtail | |||
|---|---|---|---|---|---|---|---|---|
| C1168 | INLINE | BK | 12C50814B485 | See Below | ||||
| Terminal Part Number | Service Part Number | Size |
|---|---|---|
| 2L1T-14421-CA | EU2Z-14421-CA | 1.5 |
MALE
Harness
12C508
| Pin | Circuit | Gauge | Qualifier | Terminal Part Number | ||
| 1 | RE207 (GN-VT) | 16 | 2L1T-14421-CA | |||
| 2 | CE207 (VT-GY) | 16 | 2L1T-14421-CA | |||
| 3 | RE206 (BU-OG) | 16 | 2L1T-14421-CA | |||
| 4 | CE206 (GY-YE) | 16 | 2L1T-14421-CA | |||
| 5 | RE205 (YE-BU) | 16 | 2L1T-14421-CA | |||
| 6 | CE205 (GN-BU) | 16 | 2L1T-14421-CA | |||
FEMALE
Harness
14B485
| Pin | Circuit | Gauge | Qualifier | Terminal Part Number | ||
| 1 | RE207 (GN-VT) | 16 | 7C3T-14474-DA | |||
| 2 | CE207 (VT-GY) | 16 | 7C3T-14474-DA | |||
| 3 | RE206 (BU-OG) | 16 | 7C3T-14474-DA | |||
| 4 | CE206 (GY-YE) | 16 | 7C3T-14474-DA | |||
| 5 | RE205 (YE-BU) | 16 | 7C3T-14474-DA | |||
| 6 | CE205 (GN-BU) | 16 | 7C3T-14474-DA | |||
Available Pigtail Kits
Pigtail Kit Part Number WPT-1426
Service Part Number:
FU2Z-14S411-TA
Gauge:
16
Pin material:
Silver
Cavities:
6
Vehicle Uses:
- Camera - Reverse Park Aid
- Lamp - Park/Turn/Stop
- Sensor - Coolant Temperature
- Sensor - O2 (HEGO/ EGO)
Pigtail Kit Part Number WPT-971
Service Part Number:
3U2Z-14S411-FEAB
Gauge:
14
Pin material:
Silver
Cavities:
6
Vehicle Uses:
- Connector - Inline
- Lamp - Headlamp - High/Low Beam
- Lamp - Park/Turn/Stop
- Motor - Engine Cooling Fan
- Motor - Running Board
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.