Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014TAURUS LIMITED, 2.0L ENG VIN 9REPAIR AND DIAGNOSISENGINE MECHANICALCOOLING SYSTEM (MECHANICAL)ENGINE COOLING SYSTEMSPECIFICATIONSTORQUE SPECIFICATIONS
2014 Ford Taurus Limited, 2.0L Eng VIN 9
Torque Specifications
2014 Ford Taurus Limited, 2.0L Eng VIN 9SECTION Torque Specifications
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in | ||||
|---|---|---|---|---|---|---|---|
| A/C condenser-to-Charge Air Cooler (CAC) bolts | 6 | - | 53 | ||||
| A/C condenser-to-radiator bolts | 6 | - | 53 | ||||
| Battery tray bracket bolt | 25 | 18 | - | ||||
| Block heater | 40 | 30 | - | ||||
| CAC adapter bolts | 8 | - | 71 | ||||
| CAC outlet pipe clamps | 5 | - | 44 | ||||
| CAC -to-radiator bolts | 6 | - | 53 | ||||
| CAC tube clamps | 5 | - | 44 | ||||
| Camshaft sprocket bolt(1) | - | - | - | ||||
| Coolant inlet connection bolts | 10 | - | 89 | ||||
| Coolant pump bolts - 2.0L GTDI | 10 | - | 89 | ||||
| Coolant pump bolts - 3.5L Ti-VCT, 3.5L GTDI (1) | - | - | - | ||||
| Coolant pump pulley bolts | 20 | - | 177 | ||||
| Cooling fan motor and shroud bolts | 6 | - | 53 | ||||
| Degas bottle bolts | 9 | - | 80 | ||||
| Engine oil filter (2) | - | - | - | ||||
| KS bolt | 20 | - | 177 | ||||
| Oil pan drain plug | 27 | 20 | - | ||||
| Primary timing chain guide bolts | 10 | - | 89 | ||||
| Primary timing chain tensioner bolts | 10 | - | 89 | ||||
| Radiator bracket bolts | 5 | - | 44 | ||||
| Skid plate bolts | 70 | 52 | - | ||||
| Temperature control valve nuts | 9 | - | 80 | ||||
| Thermostat housing bolts - 2.0L GTDI | 10 | - | 89 | ||||
| Thermostat housing bolts - 3.5L Ti-VCT(1) | - | - | - | ||||
| Transaxle shift cable bracket bolts | 12 | - | 106 | ||||
| Turbocharger coolant tube banjo bolts | 40 | 30 | - | ||||
| Turbocharger coolant tube-to-cylinder head bracket nut | 10 | - | 89 | ||||
| Valve train oil tube bolts(1) | - | - | - | ||||
| VCT oil control solenoid housing bolts(1) | - | - | - | ||||
| VCT bolts(1) | - | - | - | ||||
|
|||||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.