Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014TAURUS LIMITED, 2.0L ENG VIN 9REPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXSUPPLEMENTAL RESTRAINT SYSTEM DTCSOCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) (WEIGHT SENSOR BOLT SYSTEM)
2014 Ford Taurus Limited, 2.0L Eng VIN 9
Occupant Classification System Module (OCSM) (Weight Sensor Bolt System)
2014 Ford Taurus Limited, 2.0L Eng VIN 9SECTION Occupant Classification System Module (OCSM) (Weight Sensor Bolt System)
DTC INDEX
| DTC | Description | Action To Take |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to PINPOINT TEST AL . |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to PINPOINT TEST AL . |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to PINPOINT TEST AL . |
| B0061:1C | Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range | GO to PINPOINT TEST AL . |
| B00A0:54 | Occupant Classification System: Missing Calibration | GO to PINPOINT TEST AM . |
| B00A0:67 | Occupant Classification System: Signal Incorrect After Event | CARRY OUT the OCS Zero Seat Weight Test. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM ZERO SEAT WEIGHT TEST . |
| B00A0:76 | Occupant Classification System: Wrong Mounting Position | GO to PINPOINT TEST AM . |
| B00A0:97 | Occupant Classification System: Component or System Operation Obstructed or Blocked | GO to PINPOINT TEST AN . |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery | GO to PINPOINT TEST AO . |
| B00C2:13 | Passenger Seat Occupant Classification Sensor "C": Circuit Open | GO to PINPOINT TEST AO . |
| B00C2:1A | Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Below Threshold | GO to PINPOINT TEST AO . |
| B00C2:49 | Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure | GO to PINPOINT TEST AM . |
| B00C2:81 | Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data Received | REPAIR all other OCSM DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING . |
| B00C3:12 | Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery | GO to PINPOINT TEST AP . |
| B00C3:13 | Passenger Seat Occupant Classification Sensor "D": Circuit Open | GO to PINPOINT TEST AP . |
| B00C3:1A | Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Below Threshold | GO to PINPOINT TEST AP . |
| B00C3:49 | Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure | GO to PINPOINT TEST AM . |
| B00C3:81 | Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data Received | REPAIR all other OCSM DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | INSTALL a new passenger seat track assembly with weight sensor bolts. REFER to SEATING . CLEAR all DTCs before carrying out the System Reset procedure. |
| B1A59:01 | Sensor 5 Volt Supply: General Electrical Failure | GO to PINPOINT TEST AQ . |
| B1A59:11 | Sensor 5 Volt Supply: Circuit Short to Ground | GO to PINPOINT TEST AQ . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test. GO to PINPOINT TEST AJ
. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test. GO to PINPOINT TEST AR
. |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test. GO to PINPOINT TEST AK
. |
| U0401:00 | Invalid Data Received From ECM/PCM "A": No Sub Type Information | U0401:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00. CARRY OUT the PCM Self Test. REPAIR any vehicle speed or communication-related DTCs. REFER to the DTC chart in ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) (SECTION 0) . |
| U0401:81 | Invalid Data Received From ECM/PCM "A": Invalid Serial Data Received | This DTC sets when the OCSM is not receiving the vehicle speed data that it expects from the PCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:81. CARRY OUT the PCM self test. REPAIR any DTCs. REFER to the DTC Chart in ELECTRONIC ENGINE CONTROLS or the ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) (SECTION 0) . |
| U0422:00 | Invalid Data Received From ECM/PCM "A": No Sub Type Information | U0422:00 sets in a module that is reporting a communication fault from another module on the data bus. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:00. CARRY OUT the BCM self test. REPAIR any ignition switch or communication-related DTCs. REFER to the DTC Chart in MULTIFUNCTION ELECTRONIC MODULES . |
| U0422:81 | Invalid Data Received From ECM/PCM "A": Invalid Serial Data Received | U0422:81 sets when the OCSM is not receiving the ignition status data that it expects from the BCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:81. CARRY OUT the BCM self test. REPAIR any ignition switch or communication-related DTCs. REFER to the DTC Chart in MULTIFUNCTION ELECTRONIC MODULES . |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | U0452:00 sets in a module that is reporting a communication fault from another module on the data bus. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:00. CARRY OUT RCM self test. REPAIR any SRS -related DTCs. REFER to the RCM DTC CHART . |
| U0452:81 | Invalid Data Received From Restraints Control Module: No Sub Type Information | U0452:00 sets when the OCSM is not receiving the SRS data that it expects from the RCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:81. CARRY OUT RCM self test. REPAIR any SRS -related DTCs. REFER to the RCM DTC CHART . |
| U200D:12 | Control Module Output Power A: Circuit Short To Battery | GO to PINPOINT TEST AS . |
| U200E:11 | Control Module Output Power B: Circuit Short To Ground | GO to PINPOINT TEST AT . |
| U200E:12 | Control Module Output Power B: Circuit Short To Battery | GO to PINPOINT TEST AT . |
| U200E:1A | Control Module Output Power B: Circuit Resistance Below Threshold | GO to PINPOINT TEST AT . |
| U3000:49 | Control Module: Internal Electronic Failure | REPAIR all other OCSM DTCs first. REPEAT the self-test. If U3000:49 returns, INSTALL a new OCSM. REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) . |
| U3000:53 | Control Module: Deactivated | CLEAR all OCSM DTCs and REPEAT the self-test. If U3000:53 returns, INSTALL a new OCSM. REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) . |
| U3000:54 | Control Module: Missing Calibration | CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AG . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AG . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.