Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014TAURUS LIMITED, 2.0L ENG VIN 9REPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXINFORMATION SYSTEM AND ENTERTAINMENT SYSTEM (8 INCH TOUCHSCREEN) DTCSFRONT CONTROLS INTERFACE MODULE (FCIM)
2014 Ford Taurus Limited, 2.0L Eng VIN 9
Front Controls Interface Module (FCIM)
2014 Ford Taurus Limited, 2.0L Eng VIN 9SECTION Front Controls Interface Module (FCIM)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B00D5:01 | Restraint System Passenger Disable Indicator: General Electrical Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC B00D5:01 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| B113C:11 | Hazard Switch Illumination: Circuit Short To Ground | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC B113C:11 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| B1202:01 | Restraint System Passenger Enable Indicator: General Electrical Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC B1202:01 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST Z . |
| U0257:00 | Lost Communication With Front Controls/Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES , IPC DTC Chart to RETRIEVE and FOLLOW DTCs present in the IPC. |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST G . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AF . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AG . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.