Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014TAURUS LIMITED, 2.0L ENG VIN 9REPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXINFORMATION SYSTEM AND ENTERTAINMENT SYSTEM (4.2 INCH DISPLAY) DTCSFRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM)
2014 Ford Taurus Limited, 2.0L Eng VIN 9
Front Control/Display Interface Module (FCDIM)
2014 Ford Taurus Limited, 2.0L Eng VIN 9SECTION Front Control/Display Interface Module (FCDIM)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST Z . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AA . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AD . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new Front Control/Display Interface Module (FCDIM). REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new audio FCDIM. REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AF . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AG . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.