Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSFORD2014FOCUS TITANIUM, 4D HATCHBACK, AUTOMATIC DCT TRANS, GAS/ETHANOLREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEX (EXCEPT ELECTRIC)INFORMATION & ENTERTAINMENT SYSTEM - SONY AM/FM/CD/SYNC/TOUCHSCREEN DTCSAUDIO (DSP) DIGITAL SIGNAL PROCESSING MODULE - SONY SOUND DTC TABLE
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/Ethanol
Audio (DSP) Digital Signal Processing Module - Sony Sound DTC Table
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/EthanolSECTION Audio (DSP) Digital Signal Processing Module - Sony Sound DTC Table
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST I |
| B1A01:11 | Speaker #1: Circuit Short To Ground | GO to PINPOINT TEST I |
| B1A01:12 | Speaker #1: Circuit Short To Battery | GO to PINPOINT TEST I |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST I |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST G |
| B1A02:11 | Speaker #2: Circuit Short To Ground | GO to PINPOINT TEST G |
| B1A02:12 | Speaker #2: Circuit Short To Battery | GO to PINPOINT TEST G |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST G |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST H |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to PINPOINT TEST H |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to PINPOINT TEST H |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST H |
| B1A04:01 | Speaker #4: General Electrical Failure |
|
| B1A04:11 | Speaker #4: Circuit Short To Ground |
|
| B1A04:12 | Speaker #4: Circuit Short To Battery |
|
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST O |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to PINPOINT TEST J |
| B1A06:11 | Speaker #6: Circuit Short To Ground | GO to PINPOINT TEST J |
| B1A06:12 | Speaker #6: Circuit Short To Battery | GO to PINPOINT TEST J |
| B1A06:13 | Speaker #6: Circuit Open | GO to PINPOINT TEST J |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to PINPOINT TEST K |
| B1A07:11 | Speaker #7: Circuit Short To Ground | GO to PINPOINT TEST K |
| B1A07:12 | Speaker #7: Circuit Short To Battery | GO to PINPOINT TEST K |
| B1A07:13 | Speaker #7: Circuit Open | GO to PINPOINT TEST K |
| B1A08:01 | Speaker #8: General Electrical Failure |
|
| B1A08:11 | Speaker #8: Circuit Short To Ground |
|
| B1A08:12 | Speaker #8: Circuit Short To Battery |
|
| B1A08:13 | Speaker #8: Circuit Open | GO to PINPOINT TEST L |
| B1A09:11 | Speaker #9: Circuit Short To Ground | GO to PINPOINT TEST N |
| B1A09:12 | Speaker #9: Circuit Short To Battery | GO to PINPOINT TEST N |
| B1A09:13 | Speaker #9: Circuit Open | GO to PINPOINT TEST N |
| B1A10:11 | Speaker #10: Circuit Short To Ground | GO to PINPOINT TEST N |
| B1A10:12 | Speaker #10: Circuit Short To Battery | GO to PINPOINT TEST N |
| B1A10:13 | Speaker #10: Circuit Open | GO to PINPOINT TEST N |
| U0155:00 | Lost Communication With IPCÂ Control Module: No Sub Type Information | GO to PINPOINT TEST AH |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AJ |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to PINPOINT TEST AL |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AM |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPCÂ . REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES . |
| U2014:01 | Control Module Hardware: General Electrical Failure |
|
| U2014:41 | Control Module Hardware: General Checksum Failure |
|
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTCÂ sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new audio DSPÂ module to correct the failure to retain configuration data. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTCÂ sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new audio DSPÂ module to correct the failure to retain configuration data. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTCÂ sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new audio DSPÂ module to correct the failure to retain configuration data. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . |
| U3000:41 | Control Module: General Checksum Failure |
|
| U3000:42 | Control Module: General Memory Failure |
|
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AN |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AO |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.