Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014FOCUS TITANIUM, 4D HATCHBACK, AUTOMATIC DCT TRANS, GAS/ETHANOLREPAIR AND DIAGNOSIS (SINGLE PAGE)ELECTRICALMOTORS, SWITCHES, RELAYSOEM CONNECTOR END VIEWS - EXCEPT ELECTRIC - C2086 - C9221BODY CONTROL MODULE (BCM) CONNECTOR END VIEW (C2280F)
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/Ethanol
Body Control Module (BCM) Connector End View (C2280F)
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/EthanolSECTION Body Control Module (BCM) Connector End View (C2280F)
| Pin | Circuit | Gauge | Circuit Function | Qualifier |
|---|---|---|---|---|
| 1 | CBP19 (BN-WH) | 12 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 2 | * | * | Not Used | |
| 3 | SBP24 (VT-RD) | 18 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 3 | SBP24 (VT-RD) | 22 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 4 | CBP02 (GN) | 20 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 5 | SBP27 (BU-RD) | 22 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 6 | * | * | Not Used | |
| 7 | * | * | Not Used | |
| 8 | SBP06 (BN-RD) | 14 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 9 | CBP80 (OG-BK) | 14 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 10 | CBP18 (GY-OG) | 22 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 11 | RRD11 (BN) | 22 | CTRL MOD. - ELECTROCHROMIC MIRROR | |
| 12 | CBP17 (BN-GN) | 20 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 13 | * | * | Not Used | |
| 14 | * | * | Not Used | |
| 15 | * | * | Not Used | |
| 16 | SBP08 (VT-RD) | 22 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 17 | CBP04 (YE) | 22 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 18 | SBP07 (WH-RD) | 22 | FUSE OUTPUT OR CIRCUIT BREAKER | |
| 19 | * | * | Not Used | |
| 20 | SBP26 (YE-RD) | 20 | FUSE OUTPUT OR CIRCUIT BREAKER |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.