Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014F-150 SVT RAPTOR, 4D PICKUPREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 147 (REAR DRIVE AXLE/DIFFERENTIAL - FORD 9.75-INCH RING GEAR -- F150)SPECIFICATIONS
2014 Ford F-150 SVT Raptor, 4D Pickup
Section 147 (Rear Drive Axle/Differential - Ford 9.75-Inch Ring Gear -- F150): Specifications
2014 Ford F-150 SVT Raptor, 4D PickupSECTION Specifications
WARNING: This page is about a different car, the 2012 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
MATERIAL SPECIFICATIONS
| Item | Specification | Fill Capacity |
|---|---|---|
| Additive Friction Modifier XL-3 (US); CXL-3 (Canada) |
EST-M2C118-A | 118 ml (4 oz) to be installed before axle lubricant - Not to be used with Electronic Locking Differentials (ELD) |
| Maximum Strength Retaining Compound Loctite® 638™ |
- | - |
| Motorcraft® High Contrast Hypoid Gear Marking Compound XG-14 |
- | - |
| Motorcraft® SAE 75W-140 Synthetic Rear Axle Lubricant XY-75W140-QL (US); CXY-75W140-1L (Canada) |
WSL-M2C192-A and GL-5 | 2.84L (6.0 pt) - ELD only 2.60L (5.5 pt) - Non Traction-Lok equipped 2.48L (5.25 pt) - Traction-Lok equipped |
| Premium Long-Life Grease XG-1-C or XG-1-K (US); CXG-1-C (Canada) |
ESA-M1C75-B | - |
| Silicone Gasket and Sealant TA-30 |
WSE-M4G323-A4 | - |
| Threadlock and Sealer TA-25 |
WSK-M2G351-A5 | - |
REAR AXLE BACKLASH SHIM ADJUSTMENT TABLE
| Backlash Change Required | Thickness Change Required | ||
|---|---|---|---|
| mm | In | mm | In |
| 0.025 | 0.001 | 0.050 | 0.002 |
| 0.050 | 0.002 | 0.050 | 0.002 |
| 0.076 | 0.003 | 0.101 | 0.004 |
| 0.101 | 0.004 | 0.152 | 0.006 |
| 0.127 | 0.005 | 0.152 | 0.006 |
| 0.152 | 0.006 | 0.203 | 0.008 |
| 0.177 | 0.007 | 0.254 | 0.010 |
| 0.203 | 0.008 | 0.254 | 0.010 |
| 0.228 | 0.009 | 0.304 | 0.012 |
| 0.254 | 0.010 | 0.355 | 0.014 |
| 0.279 | 0.011 | 0.355 | 0.014 |
| 0.304 | 0.012 | 0.406 | 0.016 |
| 0.330 | 0.013 | 0.457 | 0.018 |
| 0.335 | 0.014 | 0.457 | 0.018 |
| 0.381 | 0.015 | 0.508 | 0.020 |
GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| Available drive pinion shims in steps of | 0.25 mm (0.010 in) 0.254 mm (0.010 in) - 0.965 mm (0.038 in) |
| Electronic Locking Differential (ELD) side gear backlash | 0.100-1.000 mm (0.004-0.040 in) |
| Maximum differential case flange ring gear runout | 0.076 mm (0.003 in) |
| Maximum variation between ring gear teeth | 0.102 mm (0.004 in) |
| Pinion bearing preload | 1.8-3.3 Nm (16-29 lb-in) |
| Ring gear backlash | 0.203-0.304 mm (0.008-0.012 in) |
| Maximum axle shaft flange runout | 0.279 mm (0.011 in) |
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in | ||
|---|---|---|---|---|---|
| Axle vent | 18 | - | 159 | ||
| Brake hose bracket bolts | 30 | 22 | - | ||
| Brake tube/parking brake cable bracket bolt | 25 | 18 | - | ||
| RH parking brake cable bracket bolt | 30 | 22 | - | ||
| Differential bearing cap bolts | 105 | 77 | - | ||
| Differential housing cover bolts | 45 | 33 | - | ||
| Differential pinion shaft lock bolt | 30 | 22 | - | ||
| Differential ring gear bolts (1) | - | - | - | ||
| Driveshaft flange bolts | 103 | 76 | - | ||
| Electronic Locking Differential (ELD) coil screws | 5 | - | 44 | ||
| ELD electrical connector bolt | 7 | - | 62 | ||
| Fill plug | 30 | 22 | - | ||
| Handle Adapter | 2.2 | - | 20 | ||
| Lower shock absorber nuts | 90 | 66 | - | ||
| Tool 205-135 nut | 7 | - | 62 | ||
| U-bolt nut(1) | - | - | - | ||
| Wheel speed sensor bolts | 15 | - | 133 | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.