SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSFORD2014ESCAPE SE, 2.0L ENG VIN 9, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX (PARKING AID SYSTEM - WHEELS & TIRES SYSTEM)SIDE & REAR VISION DTCSSIDE OBSTACLE DETECTION CONTROL MODULE - LEFT (SOD-L) AND SIDE OBSTACLE DETECTION CONTROL MODULE - RIGHT (SOD-R)
2014 Ford Escape SE, 2.0L Eng VIN 9, AWD

Side Obstacle Detection Control Module - Left (Sod-L) And Side Obstacle Detection Control Module - Right (Sod-R)

2014 Ford Escape SE, 2.0L Eng VIN 9, AWDSECTION Side Obstacle Detection Control Module - Left (Sod-L) And Side Obstacle Detection Control Module - Right (Sod-R)
DTC INDEX

DTC Description Action
B12DA:68 Blind Spot Warning Indicator: Event Information REFER to the SYMPTOM CHART .
U0010:00 Medium Speed CAN Communication Bus: No Sub Type Information Diagnose all related BCM  Diagnostic Trouble Codes (DTCs) (U0037:88, U0040:00, U0041:00, U0043:00, U0044:00 or U0045:00) first. The SODL  or SODR  could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC  ). CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the network test with a diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0121:87 Lost Communication with ABS Module: Missing Message DISREGARD this DTC  . DIAGNOSE any other symptom or Diagnostic Trouble Codes (DTCs) present in other modules. REFER to the appropriate DTC  Chart.
U0140:00 Lost Communication with Body Control Module: No Sub Type Information DIAGNOSE all related BCM  Diagnostic Trouble Codes (DTCs) (U0037:88, U0040:00, U0041:00, U0043:00, U0044:00 or U0045:00) first. The SODL  or SODR  could not communicate with the BCM at a point in time. The fault is not currently present (the module had to communicate with the BCM  to report this DTC  to the scan tool). CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0155:01 Lost Communication With Instrument Panel Cluster (IPC) Control Module: General Electrical Failure Go to PINPOINT TEST K
U0232:00 Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information DIAGNOSE the SODL  Does Not Respond To The Diagnostic Scan Tool.
Refer to: COMMUNICATIONS NETWORK .
U0233:00 Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information DIAGNOSE the SODR  Does Not Respond To The Diagnostic Scan Tool.
Refer to: COMMUNICATIONS NETWORK .
U0300:00 Internal Control Module Software Compatibility: No Sub Type Information CLEAR the Diagnostic Trouble Codes (DTCs). Ignition OFF. Ignition ON, wait 10 seconds. CHECK the SODL  or SODR  Diagnostic Trouble Codes (DTCs), if DTC  U0300:00 is retrieved again, INSTALL a new SODL  or SODR  .
Refer to: SIDE OBSTACLE DETECTION CONTROL MODULE .
U0422:68 Invalid Data Received from Body Control Module: Event Information This DTC  sets when the SODL  or SODR  receives invalid network data from the BCM  with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM  .
Refer to: BODY CONTROL MODULE (BCM) .
U2100:00 Initial Configuration Not Complete: No Sub Type Information The SODL  or SODR  is not configured. CONFIGURE the SODL  or SODR  .
Refer to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information The SODL  or SODR  is not configured. CONFIGURE the SODL  or SODR  .
Refer to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION .
U3000:44 Control Module: Data Memory Failure Go to PINPOINT TEST H
U3000:45 Control Module: Program Memory Failure Go to PINPOINT TEST H
U3000:46 Control Module: Calibration/Parameter Memory Failure Go to PINPOINT TEST H
U3000:47 Control Module: Watchdog/Safety Microcontroller Failure CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the SODL  or SODR  self-test. If DTC  U3000:47 is retrieved again, INSTALL a new SODL  or SODR  .
Refer to: SIDE OBSTACLE DETECTION CONTROL MODULE .
U3000:48 Control Module: Supervision Software Failure Go to PINPOINT TEST H
U3000:49 Control Module: Internal Electronic Failure Go to PINPOINT TEST H
U3000:4A Control Module: Incorrect Component Installed Go to PINPOINT TEST H
U3003:62 Battery Voltage: Signal Compare Failure Go to PINPOINT TEST I
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.