Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014EDGE SE, 4D UTILITY, 3.5L ENG VIN C, FWDREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXMODULE COMMMUNICATIONS NETWORK DTCS
2014 Ford Edge SE, 4D Utility, 3.5L Eng VIN C, FWD
Module COMMMUNICATIONS Network DTCS
2014 Ford Edge SE, 4D Utility, 3.5L Eng VIN C, FWDSECTION Module COMMMUNICATIONS Network DTCS
DTC INDEX
| DTC | Description | Source | Action |
|---|---|---|---|
| U0001:88 | High Speed Controller Area Network (HS-CAN) Communication Bus; Bus Off |
|
The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring, Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures |
|
The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring, Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0028:88 | Vehicle Communication Bus A: Bus Off |
|
The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring, Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0073 | Control Module Communication Bus A Off |
|
The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring, Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0073:00 | Control Module Communication Bus A Off |
|
The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring, Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U3000:88 | Control Module: Bus Off |
|
The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring, Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.