SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014EDGE SE, 4D UTILITY, 2.0L ENG VIN 9REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 118 (MODULE CONFIGURATION SYSTEM)DIAGNOSIS AND TESTINGMODULE CONFIGURATIONINSPECTION AND VERIFICATION
2014 Ford Edge SE, 4D Utility, 2.0L Eng VIN 9

Inspection and Verification

2014 Ford Edge SE, 4D Utility, 2.0L Eng VIN 9SECTION Inspection and Verification
WARNING: This page is about a different car, the 2013 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.

This information provides step-by-step module configuration procedures. Carry out the PROGRAMMABLE MODULE INSTALLATION (PMI) PROCEDURES  when another service information directs to carry out configuration or when DTCs from the list below are present:

NOTE: Some modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous Memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
DTC CHART

DTC Description Source Action
B2477 Module Configuration Failure
  • Front Display Interface Module (FDIM)
  • Smart Junction Box (SJB)
 CARRY OUT PROGRAMMABLE MODULE INSTALLATION (PMI) . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P0315 Crankshaft Position System Variation Not Learned
  • PCM
 Using the scan tool, CARRY OUT the Misfire Monitor Neutral Profile Correction procedure, following the on-screen instructions.
P0602 Powertrain Control Module Programming Error
  • PCM
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P0603 EEPROM Malfunction: Not Configured
  • Parking Aid Module (PAM)
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P0605 Internal Control Module Read Only Memory (ROM) Error
  • PCM
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P1639 Vehicle ID Block Corrupted, Not Programmed
  • PCM
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U0300 Internal Control Module Software Incompatibility
  • PCM
  • Restraints Control Module (RCM)
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U201A:51 Control Module Main Calibration Data: Not Programmed
  • Audio Front Control Module (ACM)
  • Front Controls Interface Module (FCIM)
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2050 No Application Present
  • ABS module
  • FDIM
  • Occupant Classification System Module (OCSM)
  • SJB
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2051 One or More Calibration Files Missing / Corrupt
  • ABS module
  • FDIM
  • OCSM
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2100:00 Initial Configuration Not Complete: No Sub Type Information
  • ACM
  • Global Positioning System Module (GPSM)
  • Power Steering Control Module (PSCM)
  • RCM
  • Vehicle Dynamics Module (VDM)
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2100:00 Initial Configuration Not Complete: No Sub Type Information
  • Accessory Protocol Interface Module (APIM)
 CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING .
U2100:55 Initial Configuration Not Complete: Not Configured
  • Body Control Module B (BCM-B)
  • Instrument Panel Cluster (IPC)
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information
  • APIM
 CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information
  • ACM
  • GPSM
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2101:56 Control Module Configuration Incompatible: Invalid / Incompatible Configuration
  • IPC
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U3002:62 Vehicle Identification Number: Signal Compare Failure
  • RCM
 CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.