Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014E-150 BASE, VAN CARGO, 4.6L ENG VIN WREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXDRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM DTCSAUDIO CONTROL MODULE (ACM) - WITH NAVIGATION
2014 Ford E-150 Base, Van Cargo, 4.6L Eng VIN W
Audio Control Module (ACM) - With Navigation
2014 Ford E-150 Base, Van Cargo, 4.6L Eng VIN WSECTION Audio Control Module (ACM) - With Navigation
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B108E:63 | Display: Circuit/Component Protection Time-Out | GO to PINPOINT TEST F . |
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST I . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST I . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST L . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST L . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B121C:44 | Hard Drive: Data Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A56:21 | Antenna: Signal Amplitude < Minimum |
NOTE:
If DTC B1A56:21 sets after running the bezel diagnostic tests disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency the test will fail. Therefore test ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. DISREGARD this DTC. |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST P . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST P . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D78:13 | Auxiliary Input: Circuit Open | GO to PINPOINT TEST H . |
| B1D79:01 | Microphone Input Circuit: General Electrical Failure | GO to PINPOINT TEST N . |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to PARKING AID . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST X . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC ) Control Module: No Sub Type Information | GO to PINPOINT TEST Z . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST K . |
| U197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AD . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST F . |
| U2014:09 | Control Module Hardware: Component Failure | GO to PINPOINT TEST J . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST R . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | PROGRAM the ACM . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the ACM . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the ACM . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3000:45 | Control Module: Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:45 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AE . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AF . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.