Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014E-150 BASE, VAN CARGO, 4.6L ENG VIN WREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXDRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM DTCSACCESSORY PROTOCOL INTERFACE MODULE (APIM)
2014 Ford E-150 Base, Van Cargo, 4.6L Eng VIN W
Accessory Protocol Interface Module (APIM)
2014 Ford E-150 Base, Van Cargo, 4.6L Eng VIN WSECTION Accessory Protocol Interface Module (APIM)
DRC INDEX
| DTC | Description | Action |
|---|---|---|
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST L . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST L . |
| B1252:04 | USB Port: System Internal Failure | GO to PINPOINT TEST M . |
| B1252:11 | USB Port: Circuit Short to Ground | GO to PINPOINT TEST M . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST N . |
| U0100:00 | Lost Communication With ECM/PCM: No Sub Type Information | GO to PINPOINT TEST W . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST X . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST Y . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC ) Control Module: No Sub Type Information | GO to PINPOINT TEST Z . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST AA . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AB . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Instrument Panel Cluster (IPC). |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Global Positioning System Module (GPSM). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Audio Front Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the APIM . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the APIM . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST T . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, Refer to APIM HARDWARE TESTING . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, Refer to APIM HARDWARE TESTING . |
| U3000:88 | Control Module: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the observed symptom. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AG . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AH . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.