Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSFORD2013EXPLORER POLICE INTERCEPTOR, FWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 172 (ENGINE COOLING SYSTEM)SPECIFICATIONS
2013 Ford Explorer Police Interceptor, FWD
Section 172 (Engine Cooling System): Specifications
2013 Ford Explorer Police Interceptor, FWDSECTION Specifications
WARNING: This page is about a different car, the 2013 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
MATERIAL SPECIFICATIONS
| Item | Specification | Fill Capacity | ||
|---|---|---|---|---|
| Motorcraft® Metal Surface Prep ZC-31-A |
- | - | ||
| Motorcraft® Orange Antifreeze/Coolant Concentrated VC-3-B (US); CVC-3-B2 (Canada) |
WSS-M97B44-D | 3.7L engine: 11.7L (12.4 qt)(1) Base 5.0L engine without oil cooler: 12.4L (13.1 qt)(1) Base 5.0L engine with oil cooler: 14.4L (15.2 qt.)(1) Boss® 302 engine: 14.4L (15.2 qt)a | ||
| Motorcraft® Orange Antifreeze/Coolant Prediluted VC-3DIL-B (US); CVC-3DIL-B (Canada) |
WSS-M97B44-D2 | 3.7L engine: 11.7L (12.4 qt) Base 5.0L engine without oil cooler: 12.4L (13.1 qt) Base 5.0L engine with oil cooler: 14.4L (15.2 qt.) Boss® 302 engine: 14.4L (15.2 qt) | ||
| Motorcraft® Premium Cooling System Flush VC-1 |
ESR-M14P7-A | - | ||
|
||||
GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| Pressure Tests | |
| Complete cooling system maximum pressure | 138 kPa (20 psi) |
| Pressure relief cap | 110 kPa (16 psi) |
| Radiator (out of vehicle) | 138 kPa (20 psi) |
| Thermostat Opening Temperatures | |
| Starts to open (3.7L) | 83.9-87.8°C (183-190°F) |
| Fully open (3.7L) | 93.9°C (201°F) |
| Starts to open (5.0L, Boss® 302) | 82.2°C (180°F) |
| Fully open (5.0L, Boss® 302) | 94.5°C (202°F) |
| Starts to open (5.8L) | 86.7-90.6°C (188-195°F) |
| Fully open (5.8L) | 100°C (212°F) |
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in | ||
|---|---|---|---|---|---|
| A/C condenser bolts | 10 | - | 89 | ||
| A/C condenser nuts | 8 | - | 71 | ||
| Block heater | 40 | 30 | - | ||
| Charge air cooler hose bolt - 5.8L | 8 | - | 71 | ||
| Coolant outlet connector bolts - 5.8L | 10 | - | 89 | ||
| Coolant pump bolts - 3.7L (1) | - | - | - | ||
| Coolant pump bolt - 5.0L (1) | - | - | - | ||
| Coolant pump bolts - 5.8L | 25 | 18 | - | ||
| Coolant pump pulley bolts - 3.7L | 24 | 18 | - | ||
| Coolant pump pulley bolts - 5.0L (1) | - | - | - | ||
| Coolant pump pulley bolts - 5.8L | 25 | 18 | - | ||
| Cooling fan motor and shroud bolt and stud bolt | 8 | - | 71 | ||
| Degas bottle bolts | 8 | - | 71 | ||
| Heater outlet tube bolt - 5.0L | 10 | - | 89 | ||
| Lower splash shield bolts | 5 | - | 44 | ||
| Radiator support bracket bolts | 10 | - | 89 | ||
| Supercharger (SC) degas bottle bolt - 5.8L | 8 | - | 71 | ||
| Thermostat housing bolts - 3.7L (1) | - | - | - | ||
| Thermostat housing bolts - 5.0L | 10 | - | 89 | ||
| Thermostat housing nuts - 5.8L | 25 | 18 | - | ||
| Transmission cooler bolts (if equipped) | 8 | - | 71 | ||
| Transmission cooler tubes bracket bolt (if equipped) | 7 | - | 62 | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.