Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2010FOCUS SES, 2D COUPE, STANDARDREPAIR AND DIAGNOSISENGINE MECHANICALMECHANICALENGINE MECHANICAL - 2.0LSPECIFICATIONSTORQUE SPECIFICATIONS
2010 Ford Focus SES, 2D Coupe, Standard
Torque Specifications
2010 Ford Focus SES, 2D Coupe, StandardSECTION Torque Specifications
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in | ||
|---|---|---|---|---|---|
| Accessory drive belt idler bolt | 25 | 18 | - | ||
| Accessory drive belt splash shield bolts | 9 | - | 80 | ||
| A/C compressor bolts and stud bolt | 25 | 18 | - | ||
| A/C compressor tube bracket nut | 10 | - | 89 | ||
| A/C tube-to-compressor nut | 15 | - | 133 | ||
| Bellhousing-to-engine bolts | 48 | 35 | - | ||
| Bellhousing-to-engine stud bolt | 48 | 35 | - | ||
| Bellhousing-to-oil pan bolts | 48 | 35 | - | ||
| Block heater (if equipped) | 40 | 30 | - | ||
| Camshaft bearing caps (1) | - | - | - | ||
| Camshaft drive gear bolts (1) | - | - | - | ||
| Catalytic converter heat shield bolts | 11 | - | 97 | ||
| Catalytic converter manifold studs | 17 | - | 150 | ||
| Catalytic converter nut (1) | - | - | - | ||
| Catalytic converter support bracket bolts | 22 | 16 | - | ||
| Catalytic converter support bracket-to-engine bolts | 48 | 35 | - | ||
| Catalytic converter-to-cylinder head nuts (1) | - | - | - | ||
| Clutch pressure plate | 27 | 20 | - | ||
| Connecting rod cap bolts (1) | - | - | - | ||
| Coolant expansion tank bolts | 4 | - | 35 | ||
| Coolant outlet bolts | 10 | - | 89 | ||
| Coolant pump bolts | 10 | - | 89 | ||
| Coolant pump pulley bolts | 20 | - | 177 | ||
| Crankshaft rear seal with retainer plate bolts (1) | - | - | - | ||
| Crankshaft Position (CKP) sensor bolts (1) | - | - | - | ||
| Crankshaft pulley bolt (1) | - | - | - | ||
| Crankcase vent oil separator bolts | 10 | - | 89 | ||
| Cylinder head bolts (1) | - | - | - | ||
| Cylinder Head Temperature (CHT) sensor | 12 | - | 106 | ||
| EGR tube nut | 55 | 41 | - | ||
| EGR valve bolts | 20 | - | 177 | ||
| Engine front cover bolts (1) | - | - | - | ||
| Engine front cover lower timing hole plug | 12 | - | 106 | ||
| Engine front cover-to-oil pan bolts | 10 | - | 89 | ||
| Engine front cover upper timing hole plug | 10 | - | 89 | ||
| Engine ground cable bolt | 48 | 35 | - | ||
| Engine lifting eye bolts | 45 | 33 | - | ||
| Engine mount bolts and stud bolt | 48 | 35 | - | ||
| Engine mount nuts | 90 | 66 | - | ||
| Engine Oil Pressure (EOP) switch | 15 | - | 133 | ||
| Engine plug bolt | 20 | - | 177 | ||
| Engine-to-bellhousing bolts | 48 | 35 | - | ||
| Engine-to-bellhousing stud bolt | 48 | 35 | - | ||
| Flexplate bolts (1) | - | - | - | ||
| Flexpipe-to-muffler and tailpipe assembly nuts | 48 | 35 | - | ||
| Flywheel bolts (1) | - | - | - | ||
| Fuel rail bolt | 25 | 18 | - | ||
| Heated Oxygen Sensor (HO2S) and Catalyst Monitor Sensor (CMS) wire connector bracket nuts | 25 | 18 | - | ||
| Ignition coil-on-plug bolts | 10 | - | 89 | ||
| Intake manifold bolts | 18 | - | 159 | ||
| Knock Sensor (KS) | 20 | - | 177 | ||
| Lifting eye bolts | 45 | 33 | - | ||
| Main bearing beam bolts (1) | - | - | - | ||
| Negative battery cable ground bolt | 6 | - | 53 | ||
| Oil filter adapter bolts | 25 | 18 | - | ||
| Oil level indicator tube bolt | 10 | - | 89 | ||
| Oil pan drain plug | 28 | 21 | - | ||
| Oil pan bolts (1) | - | - | - | ||
| Oil pan-to-bellhousing bolts (1) | - | - | - | ||
| Oil pump drive chain tensioner shoulder bolt | 10 | - | 89 | ||
| Oil pump drive chain tensioner bolt | 10 | - | 89 | ||
| Oil pump bolts (1) | - | - | - | ||
| Oil pump screen and pickup tube bolts | 10 | - | 89 | ||
| Oil pump sprocket bolt | 25 | 18 | - | ||
| Oil squirters | 4 | - | 35 | ||
| Positive battery cable nut | 10 | - | 89 | ||
| Power steering tube bolt | 18 | - | 159 | ||
| Power steering tube bracket nut | 20 | - | 177 | ||
| Power steering tube clip bolt | 10 | - | 89 | ||
| Radio interference capacitor bracket bolt | 10 | - | 89 | ||
| Radio interference capacitor ground bolt | 10 | - | 89 | ||
| Spark plugs | 12 | - | 106 | ||
| Starter motor bolt | 35 | 26 | - | ||
| Starter motor stud bolt | 35 | 26 | - | ||
| Starter relay large nut | 12 | - | 106 | ||
| Starter relay small nut | 5 | - | 44 | ||
| Thermostat housing bolts | 10 | - | 89 | ||
| Timing chain guide bolts | 10 | - | 89 | ||
| Timing chain tensioner bolts | 10 | - | 89 | ||
| Torque converter-to-flexplate nuts | 35 | 26 | - | ||
| Transaxle fluid indicator tube bracket bolt | 8 | - | 71 | ||
| Transaxle mounting nut mount plate center nut | 150 | 111 | - | ||
| Transaxle mounting nut mount plate outer nuts | 48 | 35 | - | ||
| Transaxle roll-restrictor bolts | 70 | 52 | - | ||
| Valve cover retainers (1) | - | - | - | ||
| Wiring harness bracket bolts | 10 | - | 89 | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.