Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSFORD2010FOCUS SES, 2D COUPE, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXINFORMATION AND ENTERTAINMENT SYSTEMS DTCSACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTC LIST
2010 Ford Focus SES, 2D Coupe, Standard
Accessory Protocol Interface Module (APIM) DTC List
2010 Ford Focus SES, 2D Coupe, StandardSECTION Accessory Protocol Interface Module (APIM) DTC List
Accessory Protocol Interface Module (APIM) DTC List
| DTC | Description | Action |
|---|---|---|
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST L . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST L . |
| B1252:04 | USBÂ Port: System Internal Failure | GO to PINPOINT TEST Q . |
| B1252:11 | USBÂ Port: Short to Ground | GO to PINPOINT TEST Q . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST R . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to PINPOINT TEST Z . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST N . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AA . |
| U0155:00 | Lost Communication With Instrument Panel Cluster(IPC): No Sub Type Information | GO to PINPOINT TEST AB . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AD . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AF . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIMÂ or Instrument Cluster (IC). |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIMÂ or Global Positioning System Module (GPSM). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIMÂ or Audio Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | refer to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | refer to MODULE CONFIGURATION . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:04 is retrieved again, INSTALL a new APIMÂ . refer to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . TEST the system for normal operation. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new APIMÂ . refer to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . TEST the system for normal operation. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new APIMÂ . refer to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . TEST the system for normal operation. |
| U3000:88 | Control Module: Bus Off | refer to MODULE COMMUNICATIONS NETWORK . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST Y . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST X . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.