Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2010FOCUS S, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1141 (CLIMATE CONTROL)SPECIFICATIONSTORQUE SPECIFICATIONS
2010 Ford Focus S, Standard
Torque Specifications
2010 Ford Focus S, StandardSECTION Torque Specifications
WARNING: This page is about a different car, the 2008 Ford RV Cutaway, 2008 Ford Econoline, 2008 Ford E450 Super Duty, and 2008 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C clutch disc and hub bolt | 13 | 10 | - |
| A/C compressor bolts | 25 | 18 | - |
| A/C compressor fitting nuts (suction and discharge) | 15 | 11 | - |
| A/C compressor pressure relief valve | 10 | - | 89 |
| Battery tray bolts | 28 | 21 | - |
| Charge air cooler (CAC) tube clamps | 12 | 9 | - |
| Compressor suction line fitting nut | 15 | 11 | - |
| Condenser bracket bolts | 12 | 9 | - |
| Condenser fitting nuts (inlet and outlet) (4.6L, 5.4L and 6.8L) | 15 | 11 | - |
| Condenser fitting nuts (inlet and outlet) (6.0L diesel) | 8 | - | 71 |
| Cowl ground strap bolt | 8 | - | 71 |
| Evaporator inlet fitting | 18 | 13 | - |
| Evaporator inlet fitting bracket screw | 2 | - | 18 |
| Evaporator outlet fitting | 39 | 29 | - |
| High-pressure service gauge port valve cap | 0.8 | - | 7 |
| High-pressure Schrader-type valve | 2.5 | - | 22 |
| Junction box bracket bolts | 28 | 21 | - |
| Low-pressure service gauge port valve cap | 0.8 | - | 7 |
| Low-pressure Schrader-type valve | 1.8 | - | 16 |
| Oil filler tube bolt | 9 | - | 80 |
| Radiator bracket bolts | 20 | 15 | - |
| Suction accumulator bolts | 14 | 10 | - |
| Suction accumulator outlet fitting nut | 15 | 11 | - |
| Suction accumulator outlet line bracket screw | 2 | - | 18 |
| Washer reservoir filler tube bolts | 9 | - | 80 |
| Wire harness stud (RH lower front of engine) | 47 | 35 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.