Pinpoint Test D: The 4X4 Control Module Does Not Respond To The Scan Tool

Communications Network

Pinpoint Tests

Pinpoint Test D: The 4X4 Control Module Does Not Respond To The Scan Tool

Refer to Wiring Diagram Set 14 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Module Communications Network for schematic and connector information. Diagrams By Number

Refer to Wiring Diagram Set 34 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Four Wheel Drive Systems for schematic and connector information. Diagrams By Number

Normal Operation

The 4X4 control module communicates with the scan tool through the High Speed Controller Area Network (HS-CAN).

This pinpoint test is intended to diagnose the following:

- Fuse
- Wiring, terminals or connectors
- 4X4 control module




PINPOINT TEST D: THE 4X4 CONTROL MODULE DOES NOT RESPOND TO THE SCAN TOOL

NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.

NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery.

-------------------------------------------------
D1 CHECK THE 4X4 CONTROL MODULE VOLTAGE SUPPLY CIRCUITS FOR AN OPEN



- Ignition OFF.
- Disconnect: 4X4 Control Module C3184 .
- Ignition ON.
- Measure the voltage between the 4X4 control module C3184-4, circuit CBP35 (YE/GY), harness side and ground; and between the 4X4 control module C3184-5, circuit SBP11 (BU/RD), harness side and ground.




- Are the voltages greater than 10 volts?

Yes
GO to D2.

No
VERIFY the Smart Junction Box (SJB) fuses 11 (10A) and 35 (10A) are OK. If OK, REPAIR the circuit in question. If not OK, Refer to the Wiring Diagrams to identify the possible causes of the circuit short. CLEAR the DTCs. REPEAT the network test with the scan tool. Diagrams By Number

-------------------------------------------------
D2 CHECK THE 4X4 CONTROL MODULE GROUND CIRCUIT



- Ignition OFF.
- Disconnect: Negative Battery Cable .
- Measure the resistance between the 4X4 control module C3184-15, circuit GD182 (BK/GY), harness side and ground.




- Is the resistance less than 5 ohms?

Yes
GO to D3.

No
REPAIR the circuit. CONNECT the negative battery cable. CLEAR the DTCs. REPEAT the network test with the scan tool.

-------------------------------------------------
D3 CHECK THE HS-CAN CIRCUITS BETWEEN THE 4X4 CONTROL MODULE AND THE DLC FOR AN OPEN



- Measure the resistance between the 4X4 control module C3184-3, circuit VDB04 (WH/BU), harness side and the DLC C251-6, circuit VDB04 (WH/BU), harness side.




- Measure the resistance between the 4X4 control module C3184-11, circuit VDB05 (WH), harness side and the DLC C251-14, circuit VDB05 (WH), harness side.




- Are the resistances less than 5 ohms?

Yes
CONNECT the negative battery cable. GO to D4.

No
REPAIR the circuit in question. CONNECT the negative battery cable. CLEAR the DTCs. REPEAT the network test with the scan tool.

-------------------------------------------------
D4 CHECK FOR CORRECT 4X4 CONTROL MODULE OPERATION



- Disconnect the 4X4 control module connector.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect the 4X4 control module connector and make sure it seats correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?

Yes
INSTALL a new 4X4 control module. REFER to Transfer Case. CLEAR the DTCs. REPEAT the network test with the scan tool.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.

-------------------------------------------------