Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2009RV CUTAWAY 6.8 SREPAIR AND DIAGNOSIS (SINGLE PAGE)GENERAL INFORMATIONDTC INDEXENTERTAINMENT SYSTEM DTCSAUDIO CONTROL MODULE (ACM) - WITH NAVIGATION DTC CHART
2009 Ford RV Cutaway 6.8 S
Audio Control Module (ACM) - With Navigation DTC Chart
2009 Ford RV Cutaway 6.8 SSECTION Audio Control Module (ACM) - With Navigation DTC Chart
AUDIO CONTROL MODULE (ACM) - WITH NAVIGATION DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | Go To PINPOINT TEST I . |
| B119F:13 | GPS Antenna: Circuit Open | Go To PINPOINT TEST I . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A01:01 | Speaker #1: General Electrical Failure | Go To PINPOINT TEST C . |
| B1A02:01 | Speaker #2: General Electrical Failure | Go To PINPOINT TEST C . |
| B1A03:01 | Speaker #3: General Electrical Failure | Go To PINPOINT TEST C . |
| B1A04:01 | Speaker #4: General Electrical Failure | Go To PINPOINT TEST C . |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | Go To PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | DISREGARD the DTC. The vehicle is not equipped with factory-installed satellite radio. |
| B1A89:13 | Satellite Antenna: Circuit Open | DISREGARD the DTC. The vehicle is not equipped with factory-installed satellite radio. |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D78:13 | Auxiliary Input: Circuit Open | Go To PINPOINT TEST H . |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to PARKING AID article. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | Go To PINPOINT TEST L . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC ) Control Module: No Sub Type Information | If the speed sensitive volume is inoperative, Go To PINPOINT TEST G . If the navigation is inaccurate, Go To PINPOINT TEST J . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | Go To PINPOINT TEST K . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | Go To PINPOINT TEST F . |
| U2014:09 | Control Module Hardware: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:09 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | DISREGARD the DTC. The vehicle is not equipped with factory-installed satellite radio. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION article. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION article. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | Go To PINPOINT TEST M . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | Go To PINPOINT TEST N . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.