Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2009PICKUP F350 SUPER DUTY, 2D PICKUP, 6.8 Y, RWD, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX -- F150SUPPLEMENTAL RESTRAINTS SYSTEMS DTCSOCCUPANT CLASSIFICATIONS SYSTEM MODULE (OCSM)
2009 Ford Pickup F350 Super Duty, 2D Pickup, 6.8 Y, RWD, Standard
Occupant Classifications System Module (OCSM)
2009 Ford Pickup F350 Super Duty, 2D Pickup, 6.8 Y, RWD, StandardSECTION Occupant Classifications System Module (OCSM)
OCCUPANT CLASSIFICATIONS SYSTEM MODULE (OCSM) DIAGNOSTIC TROUBLE CODE (DTC) CHART
| DTC | Description | Action To Take |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | Go To PINPOINT TEST AA . |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | Go To PINPOINT TEST AA . |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | Go To PINPOINT TEST AA . |
| B0061:1A | Passenger Seatbelt Tension Sensor: Circuit Resistance Below Threshold | Go To PINPOINT TEST AA . |
| B0061:1C | Passenger Seatbelt Tension Sensor: Circuit Voltage out of Range | Go To PINPOINT TEST AA . |
| B00A0:54 | Occupant Classification System: Missing Calibration | Go To PINPOINT TEST AB . |
| B00A0:67 | Occupant Classification System: Signal Incorrect After Event | CARRY out the Occupant Classification Sensor (OCS) system zero seat weight test. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM ZERO SEAT WEIGHT TEST . |
| B00A0:76 | Occupant Classification System: Wrong Mounting Position | Go To PINPOINT TEST AB . |
| B00A0:97 | Occupant Classification System: Component or System Operation Obstructed or Blocked | Go To PINPOINT TEST AC . |
| B00C0:12 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery | Go To PINPOINT TEST AD . |
| B00CO:13 | Passenger Seat Occupant Classification Sensor "A": Circuit Open | Go To PINPOINT TEST AD . |
| B00C0:1A | Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Blow Threshold | Go To PINPOINT TEST AD . |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | Go To PINPOINT TEST AB . |
| B00C0:81 | Passenger Seat Occupant Classification Sensor "A": Invalid Serial Data | CARRY out the OCS system reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET . |
| B00C1:12 | Passenger Seat Occupant Classification Sensor "B": Circuit Short To Battery | Go To PINPOINT TEST AE . |
| B00C1:13 | Passenger Seat Occupant Classification Sensor "B": Circuit Open | Go To PINPOINT TEST AE . |
| B00C1:1A | Passenger Seat Occupant Classification Sensor "B": Circuit Resistance Blow Threshold | Go To PINPOINT TEST AE . |
| B00C1:49 | Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure | Go To PINPOINT TEST AB . |
| B00C1:81 | Passenger Seat Occupant Classification Sensor "B": Invalid Serial Data | CARRY out the OCS system reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET . |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery | Go To PINPOINT TEST AF . |
| B00C2:13 | Passenger Seat Occupant Classification Sensor "C": Circuit Open | Go To PINPOINT TEST AF . |
| B00C2:1A | Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Blow Threshold | Go To PINPOINT TEST AF . |
| B00C2:49 | Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure | Go To PINPOINT TEST AB . |
| B00C2:81 | Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data | CARRY out the OCS system reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET . |
| B00C3:12 | Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery | Go To PINPOINT TEST AG . |
| B00C3:13 | Passenger Seat Occupant Classification Sensor "D": Circuit Open | Go To PINPOINT TEST AG . |
| B00C3:1A | Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Blow Threshold | Go To PINPOINT TEST AG . |
| B00C3:49 | Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure | Go To PINPOINT TEST AB . |
| B00C3:81 | Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data | CARRY out the OCS system reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | INSTALL new passenger seat track assembly with weight sensor bolts. REFER to OCCUPANT CLASSIFICATION SENSOR . |
| B1A59:01 | Sensor 5 Volt Supply: General Electrical Failure | Go To PINPOINT TEST AH . |
| B1A59:11 | Sensor 5 Volt Supply: Circuit Short to Ground | Go To PINPOINT TEST AH . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | U0100:00 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0100:00. REFER to MODULE COMMUNICATIONS NETWORK to diagnose lost communication with the PCM. |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | U0151:00 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new Occupant Classification System Module (OCSM) as part of repair for DTC U0151:00. REFER to MODULE COMMUNICATIONS NETWORK to diagnose lost communication with the RCM . |
| U0401:00 | Invalid Data Received From ECM/PCM "A": No Sub Type Information | U0401:00 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00. CARRY OUT PCM Self Test. REPAIR any speed-related DTCs. REFER to DTC chart in INTRODUCTION - GASOLINE MODELS . |
| U200D:12 | Control Module Output Power A: Circuit Short To Battery | Go To PINPOINT TEST AI . |
| U200E:11 | Control Module Output Power B: Circuit Short To Ground | Go To PINPOINT TEST AJ . |
| U200E:12 | Control Module Output Power B: Circuit Short To Battery | Go To PINPOINT TEST AJ . |
| U200E:1A | Control Module Output Power B: Circuit Resistance Below Threshold | Go To PINPOINT TEST AJ . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new OCSM . REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) . |
| U3000:53 | Control Module: Deactivated | INSTALL a new OCSM . REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) . |
| U3000:54 | Control Module: Missing Calibration | CARRY out the OCS system reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | Go To PINPOINT TEST Z . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | Go To PINPOINT TEST Z . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.