Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2009PICKUP F350 SUPER DUTY, 2D PICKUP, 6.8 Y, 4WD, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX -- F150SUPPLEMENTAL RESTRAINTS SYSTEMS DTCSRESTRAINTS CONTROL MODULE (RCM)
2009 Ford Pickup F350 Super Duty, 2D Pickup, 6.8 Y, 4WD, Standard
Restraints Control Module (RCM)
2009 Ford Pickup F350 Super Duty, 2D Pickup, 6.8 Y, 4WD, StandardSECTION Restraints Control Module (RCM)
RESTRAINT CONTROL MODULE (RCM) DIAGNOSTIC TROUBLE CODE (DTC) CHART
| DTC | Description | Action To Take |
|---|---|---|
| Continuous lamp | The Air Bag Indicator is Illuminated Continuously | Go To PINPOINT TEST A . |
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST B . |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST B . |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | Go To PINPOINT TEST B . |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | Go To PINPOINT TEST B . |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST C . |
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST C . |
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | Go To PINPOINT TEST C . |
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | Go To PINPOINT TEST C . |
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0004:11 | Driver Knee Bolster Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0004:12 | Driver Knee Bolster Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0004:13 | Driver Knee Bolster Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0004:1A | Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0004:2B | Driver Knee Bolster Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0004:4A | Driver Knee Bolster Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0005:11 | Collapsible Steering Column Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0005:12 | Collapsible Steering Column Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0005:13 | Collapsible Steering Column Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0005:1A | Collapsible Steering Column Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0005:2B | Collapsible Steering Column Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0005:4A | Collapsible Steering Column Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST D . |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST D . |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | Go To PINPOINT TEST D . |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | Go To PINPOINT TEST D . |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST E . |
| B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST E . |
| B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | Go To PINPOINT TEST E . |
| B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | Go To PINPOINT TEST E . |
| B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0020:11 | Left Side Airbag Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST F . |
| B0020:12 | Left Side Airbag Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST F . |
| B0020:13 | Left Side Airbag Deployment Control: Circuit Open | Go To PINPOINT TEST F . |
| B0020:1A | Left Side Airbag Deployment Control 1: Circuit Resistance Below Threshold | Go To PINPOINT TEST F . |
| B0020:2B | Left Side Airbag Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0020:4A | Left Side Airbag Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0021:11 | Left Curtain Deployment Control 1: Circuit Short to Ground | Go To PINPOINT TEST G . |
| B0021:12 | Left Curtain Deployment Control 1: Circuit Short to Battery | Go To PINPOINT TEST G . |
| B0021:13 | Left Curtain Deployment Control 1: Circuit Open | Go To PINPOINT TEST G . |
| B0021:1A | Left Curtain Deployment Control 1: Circuit Resistance Below Threshold | Go To PINPOINT TEST G . |
| B0021:2B | Left Curtain Deployment Control 1: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0021:4A | Left Curtain Deployment Control 1: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0028:11 | Right Side Airbag Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST H . |
| B0028:12 | Right Side Airbag Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST H . |
| B0028:13 | Right Side Airbag Deployment Control: Circuit Open | Go To PINPOINT TEST H . |
| B0028:1A | Right Side Airbag Deployment Control 1: Circuit Resistance Below Threshold | Go To PINPOINT TEST H . |
| B0028:2B | Right Side Airbag Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0028:4A | Right Side Airbag Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0029:11 | Right Curtain Deployment Control 1: Circuit Short to Ground | Go To PINPOINT TEST I . |
| B0029:12 | Right Curtain Deployment Control 1: Circuit Short to Battery | Go To PINPOINT TEST I . |
| B0029:13 | Right Curtain Deployment Control 1: Circuit Open | Go To PINPOINT TEST I . |
| B0029:1A | Right Curtain Deployment Control 1: Circuit Resistance Below Threshold | Go To PINPOINT TEST I . |
| B0029:2B | Right Curtain Deployment Control 1: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0029:4A | Right Curtain Deployment Control 1: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | Go To PINPOINT TEST J . |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | Go To PINPOINT TEST J . |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | Go To PINPOINT TEST J . |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | Go To PINPOINT TEST J . |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | Go To PINPOINT TEST K . |
| B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | Go To PINPOINT TEST K . |
| B0052:13 | Passenger Seatbelt Sensor: Circuit Open | Go To PINPOINT TEST K . |
| B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | Go To PINPOINT TEST K . |
| B0052:2B | Passenger Seatbelt Sensor: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0080:11 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0080:12 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0080:13 | Driver Seatbelt Load Limiter Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0080:1A | Driver Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0080:2B | Driver Seatbelt Load Limiter Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0080:4A | Driver Seatbelt Load Limiter Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B0090:11 | Left Frontal Restraints Sensor: Circuit Short to Ground | Go To PINPOINT TEST L . |
| B0090:4A | Left Frontal Restraints Sensor: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0090:81 | Left Frontal Restraints Sensor: Invalid Serial Data Received | Go To PINPOINT TEST L . |
| B0090:93 | Left Frontal Restraints Sensor: No Operation | Go To PINPOINT TEST L . |
| B0090:96 | Left Frontal Restraints Sensor: Component Internal Failure | Go To PINPOINT TEST L . |
| B0091:11 | Left Side Restraints Sensor 1: Circuit Short to Ground | Go To PINPOINT TEST M . |
| B0091:4A | Left Side Restraints Sensor 1: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0091:81 | Left Side Restraints Sensor 1: Invalid Serial Data Received | Go To PINPOINT TEST M . |
| B0091:93 | Left Side Restraints Sensor 1: No Operation | Go To PINPOINT TEST M . |
| B0091:96 | Left Side Restraints Sensor 1: Component Internal Failure | Go To PINPOINT TEST M . |
| B0092:11 | Left Side Restraints Sensor 2: Circuit Short to Ground | Go To PINPOINT TEST N . |
| B0092:4A | Left Side Restraints Sensor 2: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0092:81 | Left Side Restraints Sensor 2: Invalid Serial Data Received | Go To PINPOINT TEST N . |
| B0092:93 | Left Side Restraints Sensor 2: No Operation | Go To PINPOINT TEST N . |
| B0092:96 | Left Side Restraints Sensor 2: Component Internal Failure | Go To PINPOINT TEST N . |
| B0095:11 | Right Frontal Restraints Sensor: Circuit Short to Ground | Go To PINPOINT TEST O . |
| B0095:4A | Right Frontal Restraints Sensor: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0095:81 | Right Frontal Restraints Sensor: Invalid Serial Data Received | Go To PINPOINT TEST O . |
| B0095:93 | Right Frontal Restraints Sensor: No Operation | Go To PINPOINT TEST O . |
| B0095:96 | Right Frontal Restraints Sensor: Component Internal Failure | Go To PINPOINT TEST O . |
| B0096:11 | Right Side Restraints Sensor 1: Circuit Short to Ground | Go To PINPOINT TEST P . |
| B0096:4A | Right Side Restraints Sensor 1: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0096:81 | Right Side Restraints Sensor 1: Invalid Serial Data Received | Go To PINPOINT TEST P . |
| B0096:93 | Right Side Restraints Sensor 1: No Operation | Go To PINPOINT TEST P . |
| B0096:96 | Right Side Restraints Sensor 1: Component Internal Failure | Go To PINPOINT TEST P . |
| B0097:11 | Right Side Restraints Sensor 2: Circuit Short to Ground | Go To PINPOINT TEST Q . |
| B0097:4A | Right Side Restraints Sensor 2: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B0097:81 | Right Side Restraints Sensor 2: Invalid Serial Data Received | Go To PINPOINT TEST Q . |
| B0097:93 | Right Side Restraints Sensor 2: No Operation | Go To PINPOINT TEST Q . |
| B0097:96 | Right Side Restraints Sensor 2: Component Internal Failure | Go To PINPOINT TEST Q . |
| B00A0:09 | Occupant Classification System: Component Failure | Go To PINPOINT TEST R . |
| B00A0:4A | Occupant Classification System: Incorrect Component Installed | Go To PINPOINT TEST R . |
| B00A0:63 | Occupant Classification System: Circuit/Component Protection Time-Out | Go To PINPOINT TEST R . |
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure | Go To PINPOINT TEST R . |
| B00A0:68 | Occupant Classification System: Event Information | Go To PINPOINT TEST R . |
| B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | Go To PINPOINT TEST S . |
| B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | Go To PINPOINT TEST S . |
| B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | Go To PINPOINT TEST S . |
| B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | Go To PINPOINT TEST S . |
| B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short to Ground | Go To PINPOINT TEST T . |
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short to Battery | Go To PINPOINT TEST T . |
| B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | Go To PINPOINT TEST T . |
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B00DF:4A | Passenger Restraints Disable Switch: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | This DTC indicates the vehicle has been involved in a collision. INSTALL a new RCM and impact sensors. REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT . |
| B11CD:11 | Driver Frontal Airbag Canister Vent: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B11CD:12 | Driver Frontal Airbag Canister Vent: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B11CD:13 | Driver Frontal Airbag Canister Vent: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B11CD:1A | Driver Frontal Airbag Canister Vent: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B11CD:2B | Driver Frontal Airbag Canister Vent: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B11CD:4A | Driver Frontal Airbag Canister Vent: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1211:11 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST U . |
| B1211:12 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST U . |
| B1211:13 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | Go To PINPOINT TEST U . |
| B1211:1A | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | Go To PINPOINT TEST U . |
| B1211:2B | Driver Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B1211:4A | Driver Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| B1212:11 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1212:12 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1212:13 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1212:1A | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1212:2B | Driver Seatbelt Buckle Pretensioner Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1212:4A | Driver Seatbelt Buckle Pretensioner Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B1214:11 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | Go To PINPOINT TEST V . |
| B1214:12 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | Go To PINPOINT TEST V . |
| B1214:13 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | Go To PINPOINT TEST V . |
| B1214:1A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | Go To PINPOINT TEST V . |
| B1214:2B | Passenger Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | Go To PINPOINT TEST W . |
| B1214:4A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | Go To PINPOINT TEST X . |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failure | Go To PINPOINT TEST Y . |
| U0028:88 | Vehicle Communication Bus A: Bus Off | Go To PINPOINT TEST Y . |
| U0154:00 | Lost Communication With Restraints Occupant Classification System Module: No Sub Type Information |
NOTE:
The DTC will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM
as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose the communication concern. |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
NOTE:
The DTC will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM
as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose the communication concern. |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
NOTE:
This DTC will set in the RCM
if a message is not received from the Accessory Protocol Interface Module (APIM). Check for additional RCM
and APIM
DTCs.REFER to the appropriate section to diagnose the DTCs. If no other DTCs are present, REFER to APIM
Software Level Check in the General Procedures portion of
INFORMATION AND ENTERTAINMENT SYSTEMS
. |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information |
NOTE:
This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| U2100:00 | Intial Configuration Not Complete: No Sub Type Information |
NOTE:
This DTC indicates Programmable Module Installation (PMI) has yet to be performed on the RCM
. CARRY OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). Use as built data when CARRYING out Programmable Module Installation (PMI) for this DTC. REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). If DTC U2200:00 is also present, use as built data when CARRYING out Programmable Module Installation (PMI). REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U3000:4A | Control Module: Incorrect Component Installed | Go To PINPOINT TEST X . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | Go To PINPOINT TEST Z . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | Go To PINPOINT TEST Z . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.