Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2009FUSION SEL, 3.0 1, FWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1332 (AUTOMATIC TRANSMISSION)ASSEMBLYTRANSMISSION
2009 Ford Fusion SEL, 3.0 1, FWD
Section 1332 (Automatic Transmission): Assembly: Transmission
2009 Ford Fusion SEL, 3.0 1, FWDSECTION Transmission
WARNING: This page is about a different car, the 2009 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
Special Tools
| Illustration | Tool Name | Tool Number |
|---|---|---|
| Adjustment Set, Transmission Band | 307-S022 (T71P-77370-A) | |
| Holding Fixture, Transmission | 307-003 (T57L-500-B) | |
| Depth Micrometer | 303-D026 (D80P-4201-A) or equivalent | |
| Alignment Gauge, TR Sensor | 307-351 (T97L-70010-A) | |
| Installer, Transmission Extension Housing Oil Seal | 307-038 (T74P-77052-A) | |
| Sizer, Piston Seal | 307-338 (T95L-70010-G) | |
| Alignment Set, Fluid Pump | 307-S039 (T74P-77103-X) | |
| Aligner, Fluid Pump Handle | 307-431 | |
| Aligner, Fluid Pump Pilot | 307-432 | |
| Gauge Bar | 307-400 | |
| Compressor, Servo Cover | 307-402 | |
| Installer, Shift Shaft Fluid Seal | 307-050 (T74P-77498-A) | |
| Handle, Torque Converter | 307-091 (T81P-7902-C) | |
| Compressor, Cushion Spring | 307-401 | |
| Aligner, Valve Body | 307-334 (T95L-70010-C) | |
| Alignment Pins, Transmission Pump | 307-399 | |
| Aligner, Flex Plate | 307-403 | |
| Air Test Plate and Gaskets, Transmission | 307-433-01, 307-433-2, 307-433-3 | |
| Installer, Drive Pinion flange | 205-479 | |
| Installer, Output Shaft Flange | 307-404 |
Material
| Item | Specification |
|---|---|
| MERCON® V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) |
MERCON® V |
| Multi-Purpose Grease XG-4 and/or XL-5 |
ESB-M1C93-B |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.