Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2009EDGE SPORT, FWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1560 (AUTOMATIC TRANSMISSION)SPECIFICATIONSEND PLAY SPECIFICATIONS
2009 Ford Edge Sport, FWD
End Play Specifications
2009 Ford Edge Sport, FWDSECTION End Play Specifications
WARNING: This page is about a different car, the 2009 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
END PLAY SPECIFICATIONS
| Transmission Overdrive End Play Dimension D | Select Thrust Washer (No. 1 Nylon) | ID: Color | |
|---|---|---|---|
| Part Number | Thickness | ||
| 38.05-38.13 mm (1.498-1.501 in) | F7TZ-TA | 1.55-1.60 mm (0.061-0.063 in) | White |
| 38.14-38.23 mm (1.50-1.51 in) | F7TZ-MA | 1.75-1.80 mm (0.069-0.071 in) | Green |
| 38.29-38.42 mm (1.507-1.513 in) | F7TZ-NA | 1.85-1.90 mm (0.073-0.075 in) | Red |
| 38.43-38.61 mm (1.51-1.52 in) | F7TZ-RA | 2.05-2.10 mm (0.081-0.083 in) | Black |
| 38.62-38.74 mm (1.52-1.53 in) | F7TZ-SA | 2.15-2.20 mm (0.095-0.097 in) | Yellow |
END PLAY SPECIFICATIONS
| Rear (No. 4) Dimension E | Selective Needle Bearings (No. 4) | ID: Notches | |
|---|---|---|---|
| Part Number | Thickness | ||
| 1.67-1.85 mm (0.066-0.073 in) | XW4Z-7D014-CA | 2.65-2.80 mm (0.104-0.110 in) | 0 |
| 1.86-2.04 mm (0.073-0.080 in) | XW4Z-7D014-DA | 2.80-2.95 mm (0.110-0.116 in) | 1 |
| 2.05-2.23 mm (0.081-0.088 in) | XW4Z-7D014-EA | 3.00-3.15 mm (0.118-0.124 in) | 2 |
| 2.25-2.43 mm (0.089-0.096 in) | XW4Z-7D014-FA | 3.20-3.35 mm (0.126-0.132 in) | 3 |
CAUTION:
Always obey local traffic laws, do not exceed posted limits.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.