2008 Ford E 450 V10-6.8LFACTORY OEM SERVICE PROCEDURE

System Specifications

Cylinder Bore Diameter
Grade 1 90.200-90.210 mm
Grade 2 90.210-90.220 mm
Grade 3 90.220-90.230 mm

Crankshaft
Main bearing journal diameter 67.481-67.505 mm
Maximum out-of-round 0.0075 mm between cross sections
Maximum taper (straightness) 0.004 mm
Runout: FIM of center journals when located on front and rear journal 0.05 mm (3 places)
Clearance - crankshaft journal-to-main bearing clearance 0.048-0.024 mm
Connecting rod journal diameter 53.003-52.983 mm
Maximum out-of-round 0.0075 mm between cross sections
Maximum taper 0.004 mm
Crankshaft end play 0.075-0.377 mm

Crankshaft Main Bearing Cap Bolts 1-12
Discard the bolts.

Stage 1 40 Nm (30 lb-ft).
Stage 2 Tighten an additional 90°

Factory service manual diagram




Crankshaft Main Bearing Cap Bolts 13-24
Discard the bolts.

Stage 1 30 Nm (22 lb-ft).
Stage 2 Tighten an additional 90°

Factory service manual diagram




Crankshaft Main Bearing Codes

Factory service manual diagram



Factory service manual diagram



Factory service manual diagram



Factory service manual diagram




Connecting Rod
Big end journal inside diameter with assembled liners 53.049-53.027 mm
Rod bearing-to-journal clearance 0.064-0.026 mm
Pin bore diameter (rod) 22.024-22.012 mm
Rod length (centerline bore-to-bore) 169.1 mm
Alignment Bore-to-bore max. twist 0.05 mm
Bore-to-bore max. bend 0.038 mm
Side play (as assembled to crank)
Standard play 0.410 ± 0.26 mm
Maximum play 0.670 min

Connecting Rod Cap Bolts
Discard the bolts.

Stage 1 43 Nm (32 lb-ft).
Stage 2 Tighten an additional 105°

Factory service manual diagram




Piston
Piston diameter (Grade 2) at right angle-to-pin bore 90.180 ± 0.005 mm
Piston-to-bore clearance (-0.005) to +0.025 mm
Pin bore diameter (piston) 22.008-22.014 mm
Pin diameter 22.0010-22.0030 mm
Clearance (neg. or pos.) 0.0139-0.005 mm
Pin bore diameter (rod) 22.012-22.024 mm
Clearance 0.009-0.023 mm
Ring groove width
Top 1.503-1.505 mm
Intermediate 1.502-1.504 mm
Oil control 3.030-3.050 mm
Piston ring gap
Top 0.15-0.30 mm
Intermediate 0.25-0.50 mm
Oil control 0.15-0.65 mm

Crankshaft Pulley Bolt
Discard the bolt.

Stage 1 90 Nm (66 lb-ft).
Stage 2 Loosen one full turn
Stage 3 50 Nm (37 lb-ft).
Stage 4 Tighten an additional 90° without exceeding 200 Nm (148 lb-ft).
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.