Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FUSION SEL, 2.3 Z, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 6 (AUTOMATIC TRANSMISSION - 6 SPEED)SPECIFICATIONSTORQUE SPECIFICATIONS
2007 Ford Fusion SEL, 2.3 Z, Standard
Torque Specifications
2007 Ford Fusion SEL, 2.3 Z, StandardSECTION Torque Specifications
WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Brake caliper hose retaining bracket bolt | 22 | 16 | - |
| Catalyst monitor sensor | 48 | 35 | - |
| Catalytic converter band clamp bolts | 20 | 15 | - |
| Catalytic converter band clamp LH half bolts | 40 | 30 | - |
| Catalytic converter band clamp RH half nuts | 20 | 15 | - |
| Catalytic converter bracket bolts | 20 | 15 | - |
| Catalytic converter-to-engine block bracket bolts | 35 | 26 | - |
| Catalytic converter-to-exhaust manifold nuts | 40 | 30 | - |
| Catalytic converter support bracket nuts | 23 | 17 | - |
| Damper fork through bolt | 103 | 76 | - |
| Driveshaft bolts | 70 | 52 | - |
| EGR tube | 40 | 30 | - |
| EGR valve bolts | 25 | 18 | - |
| Front wheel hub nut | 225 | 185 | - |
| Ground wire bolts | 12 | 9 | - |
| Heated oxygen sensor (HO2S) | 48 | 35 | - |
| HO2S bracket bolt | 12 | 9 | - |
| Lower control arm nuts | 200 | 148 | - |
| Main control valve body boltsa | - | - | - |
| Manual control lever nut | 12 | 9 | - |
| Power steering gear bolts | 107 | 79 | - |
| Power steering line bracket retaining bolts | 9 | - | 80 |
| Power steering line bracket-to-cylinder head retaining bolt | 7 | - | 62 |
| Power transfer unit (PTU) bolts | 90 | 66 | - |
| PTU support bracket bolts | 70 | 52 | - |
| RH exhaust manifold heat shield bolts | 11 | 8 | - |
| RH halfshaft bearing support bracket bolts (all wheel drive [AWD]) | 23 | 17 | - |
| RH halfshaft bearing support bracket bolts (front wheel drive [FWD]) | 55 | 41 | - |
| Selector lever cable bracket bolts | 12 | 9 | - |
| Selector lever cable bracket nut | 12 | 9 | - |
| Stabilizer link nuts | 40 | 30 | - |
| Starter B+ cable | 12 | 9 | - |
| Starter bolts | 26 | 19 | - |
| Starter cable (small) | 5 | - | 44 |
| Subframe nuts | 150 | 111 | - |
| Subframe support bracket bolts | 103 | 76 | - |
| Torque converter nuts | 36 | 27 | - |
| Transaxle insulator-to-frame boltsb | 62 | 46 | - |
| Transaxle roll restrictor boltsb | 90 | 66 | - |
| Transaxle support insulator bracket bolt | 80 | 59 | - |
| Transaxle support insulator bracket nuts | 80 | 59 | - |
| Transaxle support insulator bracket through bolt (3.5L engine) | 130 | 96 | - |
| Transaxle support insulator-to-bracket bolts (3.0L engine) | 90 | 66 | - |
| Transaxle-to-engine bolts (3.0L engine) | 40 | 30 | - |
| Transaxle-to-engine bolts (3.5L engine) | 48 | 35 | - |
| Transmission control module (TCM) | 24 | 18 | - |
| Transmission fluid cooler tubes | 10 | - | 89 |
| Transmission fluid drain plug | 47 | 35 | - |
| Transmission fluid fill plug | 39 | 29 | - |
| Transmission fluid pan bolts | 13 | 10 | - |
| Transmission fluid temperature (TFT) sensor | 10 | - | 89 |
| Y-pipe bolts | 40 | 30 | - |
| Y-pipe nuts | 40 | 30 | - |
a Refer to the appropriate procedures.
b When reinstalling fasteners originally coated with Loctite, clean the fasteners with a wire brush prior to applying new threadlock. Apply threadlock and sealer to threads of the bolt.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.