Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSFORD2007FUSION SEL, 2.3 Z, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 6 (AUTOMATIC TRANSMISSION - 6 SPEED)DIAGNOSTIC TESTSDIAGNOSTIC PARAMETERS IDENTIFICATION (PID) CHART

2007 Ford Fusion SEL, 2.3 Z, Standard

Diagnostic Parameters Identification (PID) Chart

2007 Ford Fusion SEL, 2.3 Z, StandardSECTION Diagnostic Parameters Identification (PID) Chart

WARNING: This page is about a different variant/trim than selected.

Special Tools

Illustration	Tool Name	Tool Number
	Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) software with appropriate hardware, or equivalent scan tool

PID Name	Description	Units
TORQUE	Net engine torque	Torque (lb-ft)
TCC_AMP	Converter pressure control	Current (amps)
SSE_AMP	Shift solenoid pressure control E	Current (amps)
TCCPC	Converter pressure control	Pressure (psi)
SSPCE	Shift solenoid pressure control E	Pressure (psi)
SSPCE_F	SSPCE status	00 is not fault detected 01 is short circuit to ground 02 is open circuit load 04 is short circuit to battery power 80 is general (non-specific) fault
GEAR_OSC	Gear commanded by output state control	0 = commanded gear is not controlled by OSC 2 = 1st gear is commanded by OSC 4 = 2nd gear is commanded by OSC 12 = 6th gear is commanded by OSC
TCC_OSC	Output state control of torque converter	00 TCC not controlled by OSC 01 TCC is disengaged by OSC 02 TCC is engaged by OSC
SSPCD_F	SSPCD status	00 is not fault detected 01 is short circuit to ground 02 is open circuit load 04 is short to battery power 80 is general (non specific) fault
TSS_SRC	Turbine shaft speed	rpm
OSS_SRC	Output shaft speed	rpm
PCA_F	Pressure control solenoid A	INT
SSPCD	Shift solenoid pressure control D	Pressure (psi)
PCA	Pressure control solenoid A	Pressure (psi)
SSD_AMP	Shift solenoid pressure control D	Current (amps)
PCA_AMP	Pressure control solenoid A	Current (amps)
TP_REL	Relative throttle position	Percentage
DTCTCM	Continuous codes	Number of DTCs
TCCSLPDSD	Torque converter clutch slip desired	rpm
SHFTCTRL	Shift control	00 Economy mode 01 Sport mode 02 Up slope 1 mode 03 Up slope 2 mode 04 Down slope mode 05 Hot 1 (over temperature 1) mode 06 Hot 2 (over temperature 2) mode 07 Cruise mode 08 Traction mode 09 l Position mode 0A Tiptronic mode 0B Coast shift FF Invalid data
SSPCF_F	Shift solenoid pressure control F status	00 is not fault detected 01 is short to ground 02 is open circuit load 04 is short circuit to battery power 80 is general (non-specific) fault
SSFAMP_MES	Measured current SSF	Current (amps)
SSFAMP_CMD	Commanded current SSF	Current (amps)
SSPCF_CMD	Commanded pressure SSF	Pressure (psi)
SSEAMP_MES	Measured current SSE	Current (amps)
SSDAMP_MES	Measured current SSD	Current (amps)
SSCAMP_MES	Measured current SSC	Current (amps)
TCCAMP_MES	Measured current for the TCC pressure control	Current (amps)
PCAAMP_MES	Measured current for PCA	Current (amps)
SSPCC_F	SSPCC status	00 is not fault detected 01 is short to ground 02 is open circuit load 04 is short circuit to battery power 80 is general (non-specific) fault
SSPCC	Shift solenoid pressure control C	Pressure (psi)
SSC_AMP	Shift solenoid pressure control C current	Current (amps)
SSB_F	Shift solenoid 2 status	00 is not fault detected 01 is short to ground 02 is open circuit load 04 is short circuit to battery power 40 is stack failure 80 is general (non-specific) fault
SSA_F	Shift solenoid 1 status	00 is not fault detected 01 is short to ground 02 is open circuit load 04 is short circuit to battery power 80 is general (non-specific) fault
TFT	Transmission fluid temperature	Temperature (°C, °F)
TRAN_RAT	Transmission gear ratio	Ratio
TCC_F	Torque converter clutch fault	00 is not fault detected 01 is short to ground 02 is open circuit load 04 is short circuit to battery power 80 is general (non-specific) fault
VSS	Vehicle Speed	Speed (mph)
TFT	Transmission fluid temperature	Voltage
TCC_RAT	Transmission slip ratio	Ratio
TC_SLIPACT	Torque converter slip actual TCCMACT	rpm
TR	Transaxle range	P = 7 R = 6 N = 5 D = 4 L = 1
OSS	Output shaft speed	rpm
TSS	Turbine shaft speed	rpm
Gear	Gear commanded by module	Gear (1-6)
VPWRTCM	Module supply voltage VBAT	Voltage
RPMTCM	Engine revolutions per minute	rpm
TR_V	Transaxle range	Voltage

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.