Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FUSION SEL, 2.3 Z, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 552 (INSTRUMENT CLUSTER SYSTEM)DIAGNOSIS AND TESTINGINSTRUMENT CLUSTERINSTRUMENT CLUSTER DIAGNOSTIC TROUBLE CODE (DTC) INDEX
2007 Ford Fusion SEL, 2.3 Z, Standard
Instrument Cluster Diagnostic Trouble Code (DTC) Index
2007 Ford Fusion SEL, 2.3 Z, StandardSECTION Instrument Cluster Diagnostic Trouble Code (DTC) Index
WARNING: This page is about a different car, the 2006 Mercury Montego, 2006 Ford Freestyle, and 2006 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
INSTRUMENT CLUSTER DIAGNOSTIC TROUBLE CODE (DTC) INDEX
| DTC | Description | Source | Action |
|---|---|---|---|
| B1202 | Fuel Sender Circuit Open (sender with fuel pump module) | GO to PINPOINT TEST B . | - |
| B1204 | Fuel Sender Circuit Short To Ground (sender with fuel pump module) | GO to PINPOINT TEST B . | - |
| B1205 | Instrument Cluster Switch Number 1 Assembly Circuit Failure | Instrument Cluster | REFER to INFORMATION AND MESSAGE CENTER . |
| B1317 | Battery Voltage High | Instrument Cluster | GO to PINPOINT TEST H . |
| B1318 | Battery Voltage Low | Instrument Cluster | GO to PINPOINT TEST H . |
| B1342 | ECU is Defective | Instrument Cluster | INSTALL a new instrument cluster. REFER to INSTRUMENT CLUSTER . TEST the system for normal operation. |
| B1868 | Lamp Air Bag Warning Indicator Circuit Failure | Instrument Cluster | INSTALL as new instrument cluster. REFER to INSTRUMENT CLUSTER . TEST the system for normal operation. |
| B1870 | Lamp Air Bag Warning Indicator Circuit Short to Battery | Instrument Cluster | INSTALL as new instrument cluster. REFER to INSTRUMENT CLUSTER . TEST the system for normal operation. |
| B2143 | NVM Memory Failure | Instrument Cluster | CLEAR the DTCs. REPEAT the self-test. If DTC B2143 is still present, INSTALL a new instrument cluster. REFER to INSTRUMENT CLUSTER . |
| B2477 | Module Configuration Error | Instrument Cluster | REFER to MODULE CONFIGURATION . |
| B2627 | Fuel Sender Circuit Open #2 (secondary fuel sender) | GO to PINPOINT TEST B . | - |
| B2628 | Fuel Sender Circuit Short To Ground #2 (secondary fuel sender) | GO to PINPOINT TEST B . | - |
| B2675 | Trip Reset Button Stuck | VERIFY that the instrument cluster bezel is aligned correctly and the SELECT/RESET button is not binding. REPAIR as necessary. If the switch is not binding, INSTALL a new instrument cluster. REFER to INSTRUMENT CLUSTER . TEST the system for normal operation. | - |
| B2879 | Fuel Tank Jet Pump Fault | GO to PINPOINT TEST B . | - |
| All Other DTCs | - | Instrument Cluster | REFER to MULTIFUNCTION ELECTRONIC MODULES . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.