Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FUSION SEL, 2.3 Z, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 349 (AUTOMATIC TRANSMISSION - CD4E)DIAGNOSIS AND TESTINGDIAGNOSTIC TROUBLE CODE (DTC) TABLESNOTES
2007 Ford Fusion SEL, 2.3 Z, Standard
Diagnostic Trouble Code (DTC) Tables: Notes
2007 Ford Fusion SEL, 2.3 Z, StandardSECTION Notes
WARNING: This page is about a different car, the 2006 Mercury Mariner and 2006 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC TROUBLE CODE TABLE
| Five Digit DTC | Component | Description | Condition | Symptom | Action | ||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| P1116 | ECT | ECT out of self-test range. | ECT temperature higher or lower than expected during KOEO and KOER. | Rerun self-test at normal operating temperature. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0117 | ECT | ECT indicates 125°C (254°F). | ECT temperature higher or lower than expected during KOEO and KOER. | Torque converter clutch will always be off, resulting in poor fuel economy. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0118 | ECT | ECT indicates -40°C (-40°F). | ETC temperature higher or lower than expected during KOEO and KOER. | Torque converter clutch will always be off, resulting in poor fuel economy. | Refer to INTRODUCTION - GASOLINE . | ||||||
| PI 124 | TP | TP voltage high/low for self-test. | TP was not in the correct position for self-test. | Rerun at appropriate TP position per application. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0122, P0123, PI 120, P1121, PI 125 | TP | TP fault codes. | Processor assembly has detected an error. This error may cause a transaxle concern. Refer to INTRODUCTION - GASOLINE for diagnosis. | Harsh engagements, firm shift feel, abnormal shift schedule, torque converter clutch does not engage. Torque converter clutch cycling. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0102, P0103, PI 100, P1101 | MAF | MAF fault codes. | MAF system has a fault which may cause a transaxle concern. Refer to INTRODUCTION - GASOLINE for diagnosis. | Incorrect shift schedule, high/low EPC pressure. Incorrect converter engagement scheduling, symptoms similar to a TPS failure. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0300, P0308, P0320, P0340, P1351, P1364 | El System | El system fault codes. | Ignition system has a fault which may cause a transaxle concern. Refer to INTRODUCTION - GASOLINE for diagnosis. | Engine fault, no torque converter engagement, late WOT shifts. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P1705 | TR | TR not in PARK. | Self-test not run in PARK. | Rerun self-test in PARK. | GO to PINPOINT TEST D . | ||||||
| P1703 | BPP | Brake not actuated during self-test. | Brake not cycled during KOER. | Failed on or not connected - converter clutch will not engage at less than 1/3 throttle. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P1703 | BPP | BPP switch circuit failed. | Brake pedal position switch circuit failure. | Failed off - converter clutch will not disengage when brake is applied. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P1460 | A/C | A/C switch error. | A/C or defrost on condition may result from A/C clutch being on during quick test. | Failed ON - EPC pressure slightly low with A/C off. Failed off - EPC pressure slightly low with A/C on. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0962, P0748 | EPC | EPC solenoid circuit failure, shorted to ground. | Voltage through EPC solenoid is checked and compared to a voltage through solenoid after a time delay. An error will be noted if tolerance is exceeded. KOEO and continuous self-test. | Short to ground: limit engine torque (partial fuel shut-off, heavy misfire). Minimum line pressure. | GO to PINPOINT TEST E . | ||||||
| P0960(1) | EPC | EPC solenoid circuit failure, open circuit. | Voltage through EPC solenoid is checked and compared to a voltage through solenoid after a time delay. An error will be noted if tolerance is exceeded. KOEO and continuous self-test. | Open circuit - causes maximum EPC pressure, harsh engagements and shifts. | GO to PINPOINT TEST E . | ||||||
| P0731(2) | SSA, SSB, or internal parts | 1st gear failure. | No 1st gear. | Harsh shifts. Incorrect gear selection depending on condition mode and manual lever position: see SOLENOID OPERATION TABLE . Shift errors may also be due to other internal transaxle concerns (such as stuck valves, damaged friction material). | GO to PINPOINT TEST A . | ||||||
| P0732(2) | SSA, SSB, or internal parts | 2nd gear failure. | No 2nd gear. | Harsh shifts. Incorrect gear selection depending on condition mode and manual lever position: see SOLENOID OPERATION TABLE . Shift errors may also be due to other internal transaxle concerns (such as stuck valves, damaged friction material). | GO to PINPOINT TEST A . | ||||||
| P0733(2) | SSA, SSB or internal parts | 3rd gear failure. | No 3rd gear. | Harsh shifts. Incorrect gear selection depending on condition mode and manual lever position: see SOLENOID OPERATION TABLE . Shift errors may also be due to other internal transaxle concerns (such as stuck valves, damaged friction material). | GO to PINPOINT TEST A . | ||||||
| P0734(2) | SSA, SSB or internal parts | 4th gear failure. | No 4th gear. | Harsh shifts. Incorrect gear selection depending on condition mode and manual lever position: see SOLENOID OPERATION TABLE . Shift errors may also be due to other internal transaxle concerns (such as stuck valves, damaged friction material). | GO to PINPOINT TEST A . | ||||||
| P1780 | TCS | Transmission control switch not changing states during self-test. | Transmission control switch not cycled during self-test. Circuit open or shorted. | No overdrive cancel when switch is cycled. | Rerun self-test and cycle switch, refer to INTRODUCTION - GASOLINE . | ||||||
| P0707 | TR | TR out of range. Shorted circuit or sensor. | TR sensor, circuit or PCM shorted to ground. | Harsh shifts or engagements. | GO to PINPOINT TEST D . | ||||||
| P0708 | TR | TR out of range. Open circuit or sensor. | TR sensor, circuit or PCM indicate open. | Harsh shifts or engagements. | GO to PINPOINT TEST D . | ||||||
| P1702 | TR | Transmission range sensor circuit. | Transmission range sensor circuit intermittent. | Harsh shifts or engagements. | GO to PINPOINT TEST D . | ||||||
| P0966(1) | 3-2TV CCS | 3-2T/CCS solenoid circuit failure - short. | 3-2T/CCS circuit fails to provide voltage drop across solenoid. Circuit shorted during self-test. | Failed on - no engine braking (except in (D)), delayed 3-2 downshifts. | GO to PINPOINT TEST G . | ||||||
| P0964(1) | 3-2TV CCS | 3-2T/CCS solenoid circuit failure - open. | 3-2T/CCS circuit fails to provide voltage drop across solenoid. Circuit open or processor drive circuit failure during self-test. | Failed off - engine braking in second/third gears, firm or flared 3-2 downshifts. Harsh 4-3 downshifts. | GO to PINPOINT TEST G . | ||||||
| P1742, P1743(3) | TCC | TCC solenoid failed ON or OFF. | TCC solenoid has failed ON or OFF by electrical, mechanical or hydraulic concern. | Harsh shifts or engagements. Engine RPM higher or lower than expected. | GO to PINPOINT TEST C . | ||||||
| P0743(1), P0740(3) | TCC | Torque converter clutch solenoid circuit failure, open or shorted. | TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open, shorted or processor drive failure. | Harsh shifts or engagements. Engine RPM higher or lower than expected. | GO to PINPOINT TEST C . | ||||||
| P1744, P0741(3) | TCC | TCC function check. | Excessive slip detected during full TCC engagement. | Harsh shifts or engagements. Engine RPM higher or lower than expected. | GO to PINPOINT TEST C . | ||||||
| P0750(1), P0753(1) | SSA | SSA solenoid circuit failure, open or shorted. | Solenoid A circuit failed to provide voltage drop across solenoid. Circuit open or shorted or processor driver failure during self-test. | Incorrect gear selection depending on condition mode and manual lever position. | See the SOLENOID OPERATION TABLE , refer to PINPOINT TESTS - NON OSC EQUIPPED VEHICLE . GO to PINPOINT TEST A . | ||||||
| P1714 | SSA | SSA fault. | Mechanical failure of the solenoid detected. | Incorrect gear selection depending on condition, mode and manual lever position. | See the SOLENOID OPERATION TABLE , refer to PINPOINT TESTS - NON OSC EQUIPPED VEHICLE . GO to PINPOINT TEST H . | ||||||
| P1715 | SSB | SSB fault. | Mechanical failure of the solenoid detected. | Incorrect gear selection depending on condition, mode and manual lever position. | See the SOLENOID OPERATION TABLE , refer to PINPOINT TESTS - NON OSC EQUIPPED VEHICLE . GO to PINPOINT TEST H . | ||||||
| P0755(1), P0758(3) | SSB | SSB solenoid circuit failure, open or shorted. | Solenoid B circuit failed to provide voltage drop across solenoid. Circuit open or shorted or processor driver failure during self-test. | Incorrect gear selection depending on condition mode and manual lever position. | See the SOLENOID OPERATION TABLE , refer to PINPOINT TESTS - NON OSC EQUIPPED VEHICLE . GO to PINPOINT TEST A . | ||||||
| P0721 | OSS | OSS signal noisy. | PCM has detected a noisy OSS sensor signal. | Harsh shifts, abnormal shift schedule operation. | GO to PINPOINT TEST F . | ||||||
| P0720 | OSS | Insufficient input from OSS sensor. | PCM has detected a loss of OSS signal during operation. | Harsh shift, abnormal shift schedule operation. | GO to PINPOINT TEST F . | ||||||
| P0722 | OSS | OSS signal intermittent. | PCM has detected an intermittent OSS signal. | Harsh shift, abnormal shift schedule operation. | GO to PINPOINT TEST F . | ||||||
| P0717 | TSS | Turbine shaft speed sensor circuit - signal. | PCM has detected NO TSS signal. | Possible harsh shifts, converter locks, or engagements. | GO to PINPOINT TEST F . | ||||||
| P0715 | TSS | Insufficient input from turbine speed sensor. | PCM detected a loss of TSS signal during operation. | No torque converter engagements or harsh shifts. No 4th gear operation and engine braking in 2nd and 3rd gear. | GO to PINPOINT TEST F . | ||||||
| P0718 | TSS | Turbine shaft speed sensor circuit intermittent. | PCM has detected a noisy TSS signal. | Possible harsh shifts, converter locks or engagements. | GO to PINPOINT TEST F . | ||||||
| P0711 | TFT | Transmission Temperature sensor in range failure. | The PCM has detected no change in TFT during normal operation. | Substitute ECT temperature reading. | GO to PINPOINT TEST B . | ||||||
| P0712 | TFT | 150°C (302°F) indicated TFT sensor circuit grounded. | Voltage drop across TFT sensor exceeds temperature of 150°C (302°F). | Incorrect torque converter clutch operation. Incorrect EPC pressure control. | GO to PINPOINT TEST B . | ||||||
| P0713 | TFT | -40°C (-40°F) indicated TFT sensor circuit open. | Voltage drop across TFT sensor exceeds scale set for temperature -40°C (-40°F). | Incorrect torque converter clutch operation. Incorrect EPC pressure control. | GO to PINPOINT TEST B . | ||||||
| P1711 | TFT | TFT out of ST range. | Transaxle not at operating temperature during self-test. | Warm or cool transaxle to normal operating temperature. | GO to PINPOINT TEST B . | ||||||
| P1783 | TFT | Transmission overtemp condition indicated. | Transmission fluid temperature exceeded 127°C (270°F). | Increased line pressure. | GO to PINPOINT TEST B . | ||||||
| P1636 | Inductive signature clip | Inductive signature clip communication. | PCM has detected an internal error. | - | Refer to INTRODUCTION - GASOLINE . | ||||||
| P1782 | P/E switch | Performance/economy switch circuit out of self-test range (if equipped). | P/E switch not cycled during self-test or shorted/opened. | No change in states when cycled. | Rerun self-test and cycle switch. Refer to INTRODUCTION - GASOLINE . | ||||||
| P1501 | Vss | VSS input out of self-test range. | PCM detected presence of a VSS signal during self-test. | No transmission symptom. | Refer to INTRODUCTION - GASOLINE . | ||||||
| P0963 | EPC | EPC solenoid circuit failure, short circuit to VBAT. | Voltage through EPC solenoid is checked. An error will be noted if tolerance is exceeded. | Short to VBAT: maximum EPC pressure, harsh engagements and shifts. May flash the TCIL. | GO to PINPOINT TEST E . | ||||||
| P0778 | 3-2 T/CCS solenoid | 3-2 T/CCS solenoid or circuit electrical intermittent failures detected. | Voltage through 3-2T/CCS solenoid and circuit are checked. An error will be noted if tolerance is exceeded. | May flash the TCIL. | GO to PINPOINT TEST G . | ||||||
| P0967 | 3-2 T/CCS solenoid | 3-2 TCCS solenoid circuit failure, short circuit to VBAT. | Voltage through 3-2T/CCS solenoid and circuit are checked. An error will be noted if tolerance is exceeded. | May flash the TCIL. | GO to PINPOINT TEST G . | ||||||
|
|||||||||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.