Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FUSION SEL, 2.3 Z, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1604 (INTERIOR LIGHTING SYSTEM)DIAGNOSIS AND TESTINGINTERIOR LIGHTINGINSPECTION AND VERIFICATION
2007 Ford Fusion SEL, 2.3 Z, Standard
Inspection and Verification
2007 Ford Fusion SEL, 2.3 Z, StandardSECTION Inspection and Verification
WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
- Verify the customer concern.
- Visually inspect for obvious signs of electrical damage.VISUAL INSPECTION
Electrical - Smart Junction Box (SJB) fuse(s):
- 9 (15A)
- 10 (15A)
- 25 (10A)
- Wiring, terminals or connectors
- Bulb(s)
- Courtesy lamps
- Map lamps
- Puddle lamp(s)
- Scuff plate lamp(s) (if equipped)
- Luggage compartment lamp
- Vanity lamps
- Instrument panel dimmer switch
- Glove compartment lamp
- Ambient lighting switch (if equipped)
- Smart Junction Box (SJB) fuse(s):
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident, connect the scan tool to the Data Link Connector (DLC).
- If the scan tool does not communicate with the VCM:
- Check the VCM connection to the vehicle.
- Check the scan tool connection to the VCM.
- Refer to MODULE COMMUNICATIONS NETWORK -- FUSION, MILAN & MKZ article, No Power To The Scan Tool, to diagnose no power to the scan tool.
- If the scan tool does not communicate with the vehicle:
- Verify the ignition key is in the ON position.
- Verify the scan tool operation with a known good vehicle.
- Refer to MODULE COMMUNICATIONS NETWORK -- FUSION, MILAN & MKZ article to diagnose no response from the PCM.
- Carry out the network test.
- If the scan tool responds with no communication with the SJB, refer to MODULE COMMUNICATIONS NETWORK -- FUSION, MILAN & MKZ article.
- If the network test passes, retrieve and record the continuous memory DTCs.
- Clear the continuous DTCs and carry out the self-test diagnostics for the SJB.
- If the DTCs retrieved are related to the concern, go to DTC CHARTS . For all other DTCs, refer to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES -- FUSION, MILAN & MKZ article.
- If no DTCs related to the concern are retrieved, GO to SYMPTOM CHART .
NOTE:
Make sure to use the latest scan tool software release.
NOTE:
The Vehicle Communication Module (VCM) LED prove-out confirms power and ground from the DLC are provided to the VCM.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.