Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FUSION SEL, 2.3 Z, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1034 (MANUAL TRANSMISSION)SPECIFICATIONSTORQUE SPECIFICATIONS
2007 Ford Fusion SEL, 2.3 Z, Standard
Torque Specifications
2007 Ford Fusion SEL, 2.3 Z, StandardSECTION Torque Specifications
WARNING: This page is about a different car, the 2008 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Ball joint | 63 | 46 | - |
| Black transaxle case bolt | 65 | 48 | - |
| Clutch hydraulic line bracket bolt | 2.5 | - | 22 |
| Crossmember bolts | 115 | 85 | - |
| Drain plug | 35 | 26 | - |
| Fill level inspection plug | 35 | 26 | - |
| Final drive gear bolts | 120 | 89 | - |
| LH transaxle support insulator bolts | 48 | 35 | - |
| LH transaxle support insulator bracket nuts | 40 | 30 | - |
| LH transaxle support insulator through bolt | 103 | 76 | - |
| Mainshaft bearing retainer bolt | 7 | - | 62 |
| Reduction gear bolts | 96 | 71 | - |
| Reverse lever bracket bolts | 14 | 10 | - |
| Shift assembly bolts | 7 | - | 62 |
| Shift cable bracket bolts | 22 | 16 | - |
| Shift check bolt | 24 | 18 | - |
| Stabilizer bar link | 55 | 41 | - |
| Standard (gold) transaxle case bolts | 52 | 38 | - |
| Stopper bolt | 28 | 21 | - |
| Tie-rod end | 55 | 41 | - |
| Transaxle fill plug | 35 | 26 | - |
| Transaxle front support insulator bolts | 90 | 66 | - |
| Transaxle front support insulator bracket bolts | 48 | 35 | - |
| Transaxle front support insulator through bolt | 115 | 85 | - |
| Transaxle front-to-aft crossmember bolts | 90 | 66 | - |
| Transaxle front-to-aft crossmember nut | 175 | 129 | - |
| Transaxle rear support insulator bolt | 80 | 59 | - |
| Transaxle rear support insulator bracket bolts | 48 | 35 | - |
| Transaxle rear support insulator nuts | 80 | 59 | - |
| Transaxle rear support insulator through bolt | 115 | 85 | - |
| Transaxle-to-engine bolts | 47 | 35 | - |
| Wiring harness bracket nuts | 12 | 9 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.