Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FOCUS SES, 4D SEDAN, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)EXTERNAL PAGESDIFFERENT CARSECTION 256 (ENGINE SYSTEM)SPECIFICATIONSTORQUE SPECIFICATIONS
2007 Ford Focus SES, 4D Sedan, Standard
Torque Specifications
2007 Ford Focus SES, 4D Sedan, StandardSECTION Torque Specifications
WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in | ||
|---|---|---|---|---|---|
| A/C tube-to-front cover nut | 10 | - | 89 | ||
| A/C compressor bolts | 25 | 18 | - | ||
| Body ground strap-to-engine bolt | 6 | - | 53 | ||
| Camshaft bearing cap bolts(1) | - | - | - | ||
| Camshaft position (CMP) sensor bolt | 10 | - | 89 | ||
| Camshaft sprocket bolt(1) | - | - | - | ||
| Connecting rod bearing caps(1) | - | - | - | ||
| Crankshaft main bearing caps(1) | - | - | - | ||
| Crankshaft pulley bolt(1) | - | - | - | ||
| Crankshaft position (CKP) sensor bolt | 10 | - | 89 | ||
| Cylinder head(1) | - | - | - | ||
| Coolant bypass tube stud | 25 | 18 | - | ||
| Coolant outlet adapter | 25 | 18 | - | ||
| Coolant pump bolts | 25 | 18 | - | ||
| Coolant pump pulley bolts | 25 | 18 | - | ||
| Exhaust gas recirculation (EGR) tube | 40 | 30 | - | ||
| Engine front cover(1) | - | - | - | ||
| Engine mount bolts (W710646-S439) | 70 | 52 | - | ||
| Engine mount nuts | 90 | 66 | - | ||
| Engine block coolant drain plug | 20 | 15 | - | ||
| Exhaust manifold | 25 | 18 | - | ||
| Exhaust manifold shield bolts | 10 | - | 89 | ||
| Exhaust manifold-to-converter nuts (W705443-S900) | 48 | 35 | - | ||
| Flexplate bolts | 80 | 59 | - | ||
| Fuel rail stud bolts | 10 | - | 89 | ||
| Generator battery lead nut | 9 | - | 80 | ||
| Generator bracket bolts | 10 | - | 89 | ||
| Generator bolts | 25 | 18 | - | ||
| Ground strap nut | 10 | - | 89 | ||
| Ground wire-to-fender bolt | 10 | - | 89 | ||
| Heated oxygen sensor (HO2S) | 41 | 30 | - | ||
| Idler pulley bolt | 25 | 18 | - | ||
| Ignition coil bolts | 10 | - | 89 | ||
| Intake manifold bolts(1) | - | - | - | ||
| Intake manifold bracket bolts | 25 | 18 | - | ||
| Intake manifold shield bolts | 12 | 9 | - | ||
| Jack screws(1) | - | - | - | ||
| Motor mount-to-crossmember nuts | 60 | 44 | - | ||
| Oil filter adapter bolts | 25 | 18 | - | ||
| Oil level indicator tube bolt | 10 | - | 89 | ||
| Oil pan bolts(1) | - | - | - | ||
| Oil pan drain plug | 13 | 10 | - | ||
| Oil pump bolts | 10 | - | 89 | ||
| Oil pump screen cover and tube-to-oil pump screen cover and tube spacer bolt | 25 | 18 | - | ||
| Oil pump screen cover and tube bolts | 10 | - | 89 | ||
| Oil pump screen cover and pickup tube spacer | 25 | 18 | - | ||
| Oil pressure sender(1) | - | - | - | ||
| Oil cooler bolt | 10 | - | 89 | ||
| Power steering pump bolts | 25 | 18 | - | ||
| Power steering tube bracket nut | 10 | - | 89 | ||
| Rear main seal retainer plate | 10 | - | 89 | ||
| Spark plugs | 15 | 11 | - | ||
| Starter motor bolts(1) | - | - | - | ||
| Support bracket | 10 | - | 89 | ||
| Throttle body bolts | 10 | - | 89 | ||
| Timing chain guide bolts | 10 | - | 89 | ||
| Timing chain tensioner bolts | 25 | 18 | - | ||
| Torque converter inspection cover bolts | 19 | 14 | - | ||
| Torque converter nuts | 36 | 27 | - | ||
| Transmission mount bolts (387174-S439) | 90 | 66 | - | ||
| Transmission mount nuts (W520514-S440) | 30 | 22 | - | ||
| Transmission-to-cylinder block bracket bolt | 25 | 18 | - | ||
| Transmission-to-cylinder block bolt | 34 | 25 | - | ||
| Transmission bellhousing bolts | 48 | 35 | - | ||
| Transmission cooler tube bolt | 25 | 18 | - | ||
| Transmission cooler tube nut | 9 | - | 80 | ||
| Transmission wiring harness bracket (located at the rear of RH cylinder head) bolt and stud | 25 | 18 | - | ||
| Valve cover | 10 | - | 89 | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.