SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007FOCUS SES, 4D SEDAN, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)EXTERNAL PAGESDIFFERENT CARSECTION 1128 (AUTOMATIC TRANSMISSION - 4R70E/W, 4R75E/W)DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIESMAIN CONTROL VALVE BODYASSEMBLY
2007 Ford Focus SES, 4D Sedan, Standard

Main Control Valve Body: Assembly

2007 Ford Focus SES, 4D Sedan, StandardSECTION Assembly
WARNING: This page is about a different car, the 2008 Ford RV Cutaway, 2008 Ford Econoline, and 2008 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the main control valve body cover plate.
    1. Position the valve body cover plate gasket and cover plate.
    2. Loosely install the 2 guide pin bolts.
    3. Loosely install the bolts.
    2. Fig 1: Identifying Main Control Valve Body Cover Plate
    GF0003605Courtesy of FORD MOTOR CO.
  2. Tighten the bolts in the sequence shown.
    • Tighten to 10 Nm (89 lb-in).
    3. Fig 2: Main Control Valve Body Cover Plate Bolt Tightening Sequence
    GF0003606Courtesy of FORD MOTOR CO.
  3. Install the 8 coasting booster valve shuttle balls.
    Item Part Number Description
    1 7E195 Check ball (B9) located in the forward clutch circuit near the 3-4 shift valve
    2 7E195 Check ball (B2) located in the direct clutch circuit near the 2-3 back out valve
    3 7E195 Check ball (B3) located in the overdrive and forward clutch circuits near the 1-2 shift valve
    4 7E195 Check ball (B4) located in the reverse circuit near the orifice 1
    5 7E195 Check ball (B5) located between the reverse, LS modulator and the low reverse servo circuits
    6 7E195 Check ball (B6) located between the L, 2, 3, 4 and the torque converter clutch (TCC) circuits
    7 7E195 Check ball (B7) located between the L, 2, 3, 4 and the intermediate clutch circuits
    8 7E195 Check ball (B8) located between the forward clutch and the 23 BP circuits
    4. Fig 3: Locating Coasting Booster Valve Shuttle Balls
    GF0003602Courtesy of FORD MOTOR CO.
  4. Install the converter drain back valve and solenoid pressure supply screen.
    5. Fig 4: Locating Converter Drain Back Valve And Solenoid Pressure Supply Screen
    GF0003603Courtesy of FORD MOTOR CO.
  5. Install the separator plate and gaskets.
    6. Fig 5: Locating Separator Plate And Gaskets
    GF0003601Courtesy of FORD MOTOR CO.
  6. Install the 2 reinforcement plates and bolts.
    • Tighten to 10 Nm (89 lb-in).
    7. Fig 6: Locating Reinforcement Plate And Bolts
    GF0003600Courtesy of FORD MOTOR CO.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.