Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007ESCAPE BASE, 2.3 Z, FWD, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 17 (AUTOMATIC TRANSMISSION - (HYBRID))SPECIFICATIONSTORQUE SPECIFICATIONS
2007 Ford Escape Base, 2.3 Z, FWD, Automatic
Torque Specifications
2007 Ford Escape Base, 2.3 Z, FWD, AutomaticSECTION Torque Specifications
WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C compressor connector retainer | 25 | 18 | - |
| All-wheel drive link shaft assembly bracket bolt (6 required) | 47 | 35 | - |
| Auxiliary coolant pump bolts | 10 | - | 89 |
| Catalytic converter bracket bolt (2 required) | 25 | 18 | - |
| Catalytic converter bracket nut (2 required) | 25 | 18 | - |
| DC-to-DC converter nuts | 12 | 9 | - |
| Drain plug | 40 | 30 | - |
| Engine control harness retainer nut (2 required) | 6 | - | 53 |
| Engine support crossmember bolt (2 required) | 90 | 66 | - |
| Engine support crossmember nut | 90 | 66 | - |
| Fill plug | 40 | 30 | - |
| Front insulator bolt | 90 | 66 | - |
| Front insulator bolt (2 required) | 90 | 66 | - |
| Front insulator through bolt | 115 | 85 | - |
| Front roll restrictor bolt | 115 | 85 | - |
| Front wheel drive link shaft assembly bracket (4 required) | 47 | 35 | - |
| Lateral support crossmember bolt (4 required) | 115 | 85 | - |
| Link shaft bearing assembly-to-bracket nut (2 required) | 28 | 21 | - |
| Manual control lever retaining nut | 10 | - | 89 |
| Motor electronics coolant pump bolt (2 required) | 20 | 15 | - |
| Motor electronics coolant temperature sensor | 20 | 15 | - |
| Motor electronics cooler bolt (2 required) | 6 | - | 53 |
| Power transfer unit (PTU) heat shield bolts | 14 | 10 | - |
| PTU housing assembly-to-transaxle bolt (3 required) | 70 | 52 | - |
| PTU housing assembly-to-transaxle bolt (10 m bolt) (1 required) | 47 | 35 | - |
| PTU-to-engine support bracket bolts | 40 | 30 | - |
| Rear insulator mount bracket bolt (3 required) | 25 | 18 | - |
| Rear insulator bolt | 90 | 66 | - |
| Rear mount heat shield nut (2 required) | 38 | 28 | - |
| Rear mount nut (4 required) | 90 | 66 | - |
| Rear roll restrictor-to-lateral support crossmember bolt | 90 | 66 | - |
| Rear roll restrictor bracket bolts | 55 | 41 | - |
| Rear transaxle mount bolt | 90 | 66 | - |
| Rear transaxle mount nut (2 required) | 90 | 66 | - |
| RH engine mount bracket nut (2 required) | 90 | 66 | - |
| Selector lever bolt (4 required) | 25 | 18 | - |
| Shift cable bracket nut (2 required) | 23 | 17 | - |
| Shift cable grommet nut (2 required) | 11 | 8 | - |
| Transaxle control cable nut (2 required) | 22 | 16 | - |
| Transaxle control splash shield bolt (2 required) | 15 | 11 | - |
| Transaxle coolant tube fittings (inlet/outlet) | 50 | 37 | - |
| Transaxle damper bolts (6 required) | 29 | 21 | - |
| Transaxle ground cable nut | 20 | 15 | - |
| Transaxle harness retainer bolt | 25 | 18 | - |
| Transaxle-to-engine bolt (10 required) | 47 | 35 | - |
| Upper insulator support bolt (2 required) | 25 | 18 | - |
| Upper support bolt | 90 | 66 | - |
| Upper support nut (2 required) | 90 | 66 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.