Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007ESCAPE BASE, 2.3 Z, FWD, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 758 (MANUAL TRANSMISSION - F-150)DESCRIPTION AND OPERATIONMANUAL TRANSMISSIONEXPLODED VIEWS
2007 Ford Escape Base, 2.3 Z, FWD, Automatic
Exploded Views
2007 Ford Escape Base, 2.3 Z, FWD, AutomaticSECTION Exploded Views
WARNING: This page is about a different car, the 2007 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
| Item | Part Number | Description |
|---|---|---|
| 1 | 7029 | Shim |
| 2 | 7025 | Input shaft bearing and cup |
| 3 | 7046 | Fluid scoop ring |
| 4 | 7017 | Input shaft |
| 5 | 7120 | Input shaft needle bearing |
| 6 | 7030 | Snap ring |
| 7 | 7N112 | Spacer |
| 8 | 7C096 | Thrust bearing |
| 9 | 7107 | Synchronizer ring, 4th gear |
| 10 | 7124 | Synchronizer assembly, 3rd/4th gear |
| 11 | 7107 | Synchronizer ring, 3rd gear |
| 12 | 7107 | Synchronizer outer cone |
| 13 | 7107 | Synchronizer inner cone |
| 14 | 7101 | Mainshaft, 3rd gear |
| 15 | 7127 | Needle bearing, 3rd gear |
| 16 | 7061 | Output shaft |
| 17 | 7133 | Needle bearing, 2nd gear |
| 18 | 7102 | Mainshaft, 2nd gear |
| 19 | 7107 | Synchronizer inner cone |
| 20 | 7107 | Synchronizer outer cone |
| 21 | 7107 | Synchronizer ring, 2nd gear |
| 22 | 7124 | Synchronizer assembly, 2nd/1st gear |
| 23 | 7107 | Synchronizer ring, 1st gear |
| 24 | 7107 | Synchronizer outer cone |
| 25 | 7107 | Synchronizer inner cone |
| 26 | 7133 | Needle bearing, 1st gear |
| 27 | 7100 | Mainshaft, 1st gear |
| 28 | 7173 | Sleeve |
| 29 | 7118 | Roller bearing and cup |
| 30 | 7112 | Mainshaft 5th gear |
| 31 | 7072 | Washer |
| 32 | 7142 | Output shaft, reverse gear |
| 33 | 7R205 | Output shaft, rear roller bearing |
| 34 | 7B364 | Locking nut, output shaft rear bearing |
| 35 | - | Check ball |
| 36 | 7G450 | Vehicle speed sensor (VSS) tone wheel |
| 37 | - | Snap ring |
| Item | Part Number | Description |
|---|---|---|
| 1 | 7C434 | Spacer |
| 2 | 7065 | Countershaft front bearing |
| 3 | 7113 | Countershaft |
| 4 | 7121 | Countershaft rear bearing |
| 5 | - | Check ball |
| 6 | 7173 | Sleeve |
| 7 | 7R130 | Countershaft 5th gear needle bearing |
| 8 | 7158 | Countershaft 5th gear |
| 9 | 7107 | Synchronizer ring, 5th gear |
| 10 | 7124 | Synchronizer assembly, 5th/reverse gear |
| 11 | 7107 | Synchronizer ring, reverse gear |
| 12 | 7R482 | Thrust washer (2-piece) |
| 13 | 7C340 | Thrust washer |
| 14 | 7N270 | Countershaft reverse gear needle bearing |
| 15 | 7N040 | Countershaft reverse gear |
| 16 | 7L324 | Thrust washer, countershaft |
| 17 | 7D283 | Countershaft rear roller bearing |
| 18 | 7N170 | Locknut, countershaft |
| 19 | 7140 | Reverse idler gear shaft |
| 20 | 7N037 | Thrust washer |
| 21 | 7141 | Reverse idler gear |
| 22 | 7N037 | Thrust washer |
| 23 | 7156 | Retaining ring |
| Item | Part Number | Description |
|---|---|---|
| 1 | 7005 | Main case |
| 2 | 7L276 | Funnel |
| 3 | - | Dowel (part of 7A069) |
| 4 | 7A174 | Oil cooler tube |
| 5 | 7A069 | Extension housing (rear wheel drive [RWD]) |
| 6 | 7052 | Extension housing seal |
| 7 | 7085 | Retainer |
| 8 | 7A010 | Drain plug |
| 9 | 99511-1801 | Fill plug |
| 10 | - | Plug gaskets |
| 11 | 7564 | Clutch housing cover |
| 12 | 7050 | Bearing retainer |
| 13 | 7052 | Oil seal |
| 14 | 7040 | Oil baffle |
| 15 | 7A174 | Oil passage |
| Item | Part Number | Description |
|---|---|---|
| 1 | 7230 | 1st/2nd gear shift gate |
| 2 | 7411 | 5th/reverse gear shift gate |
| 3 | - | 5th/reverse shift rail (upper) |
| 4 | 7230 | 1st/2nd gear shift fork |
| 5 | 7240 | 1st/2nd gear shift rail |
| 6 | 7231 | 3rd/4th gear shift fork |
| 7 | 7243 | Counter lever |
| 8 | 7289 | 5th/reverse gear shift fork |
| 9 | 7242 | 5th/reverse gear shift rail (lower) |
| 10 | 7241 | 3rd/4th gear shift rail |
| 11 | 7214 | Reverse gear shift rail bolt |
| 12 | 15520 | Reverse lamp switch |
| 13 | 7C277 | Gear selector interlock sleeve |
| 14 | 7050 | Case cover |
| 15 | 7A107 | Rubber plugs |
| 16 | 7232 | 3rd/4th gear shift gate |
| 17 | 7277 | Gearshift (lower) |
| 18 | 7223 | Shift control housing gasket |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.