Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007ESCAPE BASE, 2.3 Z, FWD, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1367 (ENGINE CONTROLS - DIAGNOSTIC METHODS (HYBRID))PARAMETER IDENTIFICATION (PID)FORD TCM PID LIST
2007 Ford Escape Base, 2.3 Z, FWD, Automatic
Ford TCM PID List
2007 Ford Escape Base, 2.3 Z, FWD, AutomaticSECTION Ford TCM PID List
WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, 2011 Ford Fusion, 2010 Mercury Milan, and 2010 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
FORD TCM PID LIST
| Acronym | Description | Manufacturer Units |
|---|---|---|
| ACCESS | Access Status | Time |
| ARPMDES | Desired Engine Speed TCM Received | RPM |
| CCNT | Number Of Continuous DTCs Stored In TCM | DECIMAL |
| ENG_CTO | Vehicle Speed TCM Received | RPM |
| CONTACT | High Voltage Traction Battery Contractor Status TCM Received | OPEN/CLOSED |
| ENABL_S | Enable Status | Disable/Enable |
| GCLTEMP | Generator Motor Coil Temperature | DEGREES |
| GENMODE | Generator Operational Mode TCM Received | MODE |
| GTQ_CMD | Measured Generator Motor Torque | NM |
| GTQ_OUT | Desired Generator Motor Torque TCM Received | NM |
| G_INV_V | Actual Generator Motor Inverter Voltage | VOLTS |
| G_PHTMP | Generator Inverter Phase Temperature (Highest of 3 Phases) | DEGREES |
| G_SDN_A | Generator Motor Shutdown TCM Received | ShutDwn/Not ShutDwn |
| G_SDN_B | Generator Motor Shutdown TCM Received | ShutDwn/Not ShutDwn |
| G_SDN_C | Generator Motor Shutdown TCM Received | ShutDwn/Not ShutDwn |
| G_SPEED | Generator Motor Speed | RPM |
| HV_AMP | High Voltage Traction Battery Current TCM Received Through Communication Network | AMPERES |
| HVBAT_V | High Voltage Traction Battery Voltage TCM Received | VOLTS |
| HVINTLCK | High Voltage Interlock Circuit Status | ON/OFF |
| I_SDN_1 | Immediate Shutdown 1 Input | CHARGE/DISCHARGE |
| I_SDN_2 | Immediate Shutdown 2 Input | CHARGE/DISCHARGE |
| LF_WSPD | Front Left Wheel Speed | Km/h/MPH |
| MCLTEMP | Traction Motor Coil Temperature | DEGREES |
| MECT | Motor Electronics Coolant Temperature TCM Received | DEGREES |
| M_SDN_A | Traction Motor Shutdown TCM Received | ShutDwn/Not ShutDwn |
| M_SDN_B | Traction Motor Shutdown TCM Received | ShutDwn/Not ShutDwn |
| M_SDN_C | Traction Motor Shutdown TCM Received | ShutDwn/Not ShutDwn |
| MTQ_CMD | Desired Traction Motor Torque TCM Received | NM |
| MTQ_OUT | Measured Traction Motor Torque | NM |
| M_INV_V | Actual Traction Motor Inverter Voltage | VOLTS |
| M_PHTMP | Traction Motor Inverter Temperature (Highest of 3 Phases) | DEGREES |
| M_SPEED | Traction Motor Speed | RPM |
| PCM | ID PCM Identified | Not Stored/Stored |
| PCM_VFY | PCM Verify | YES/NO |
| PRNDL_T | Gear selector position TCM received SELECTOR | POSITION |
| RF_WSPD | Front Right Wheel Speed | Km/h/MPH |
| RPM | Engine Speed TCM Calculated | RPM |
| SERMOD | Service Mode | Mode |
| TCM_CAU | Powertrain Malfunction Indicator (Wrench) Commanded | ON/OFF |
| TCM_HAZ | Hazard Indicator Commanded | ON/OFF |
| TFT | Transaxle Fluid Temperature Input | DEGREES |
| TORQUE | Engine Torque TCM Received | LB-FT |
| TQ_DSD | Desired Torque TCM Received | NM |
| VBAT | Vehicle Power Voltage | VOLTS |
| VEHMODE | Vehicle Operational Mode TCM Received | MODE |
| VSS | Vehicle Speed TCM Calculated | km/h |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.