Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007ESCAPE BASE, 2.3 Z, FWD, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1318 (ENGINE MECHANICAL - 4.6L (2V))IN-VEHICLE SERVICINGINTAKE MANIFOLDNOTES
2007 Ford Escape Base, 2.3 Z, FWD, Automatic
Intake Manifold: Notes
2007 Ford Escape Base, 2.3 Z, FWD, AutomaticSECTION Notes
WARNING: This page is about a different car, the 2010 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.
| Item | Part Number | Description |
|---|---|---|
| 1 | W704759 | RH cowl extension retainer screw (5 required) |
| 2 | N620480 | Evaporative Emission (EVAP) canister purge valve bracket nut (2 required) |
| 3 | 19C928 | RH cowl extension |
| 4 | - | Wiring harness electrical connector |
| 5 | W704759 | LH cowl extension retainer screw (3 required) |
| 6 | 17500 | LH cowl extension |
| Item | Part Number | Description |
|---|---|---|
| 1 | 14A464 | Fuel injector electrical connector (4 required) (part of 12B637) |
| 2 | 9C490 | Brake booster vacuum hose |
| 3 | 9D289 | Evaporative Emission (EVAP) canister purge valve tube |
| 4 | 6K817 | PCV tube |
| 5 | - | Generator wiring harness retainer |
| 6 | 14A464 | Generator electrical connector (part of 12B637) |
| 7 | - | Generator B+ wiring harness retainer |
| 8 | N807309 | Generator bracket bolt (4 required) |
| 9 | 10153 | Generator bracket |
| 10 | 14A464 | Throttle control electrical connector (part of 12B637) |
| 11 | 14A464 | Throttle Position (TP) sensor electrical connector (part of 12B637) |
| 12 | 13A506 | Wire harness retainer |
| 13 | W705793 | Intake manifold crash bracket bolt |
| 14 | W701725 | Intake manifold crash bracket bolt |
| 15 | 13A506 | Wire harness retainer |
| Item | Part Number | Description |
|---|---|---|
| 1 | N807309 | Intake manifold shield bolt (2 required) |
| 2 | 9F460 | Intake manifold shield |
| 3 | 9E489 | EGR system module vacuum connector |
| 4 | 14A464 | EGR system module electrical connector (part of 12B637) |
| 5 | 9E499 | Intake manifold vacuum hose |
| 6 | 15161 | Heater hose spring clamp |
| 7 | 18D334 | Heater hose |
| 8 | 9E489 | Fuel rail pressure and temperature sensor vacuum connector |
| 9 | 14A464 | Fuel rail pressure and temperature sensor electrical connector (part of 12B637) |
| 10 | 14A464 | Fuel injector electrical connector (4 required) (part of 12B637) |
| Item | Part Number | Description |
|---|---|---|
| 1 | N808130 | Intake manifold bolt (8 required) |
| 2 | 9424 | Intake manifold |
| 3 | 9439 | Intake manifold gasket (2 required) |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.