Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007ESCAPE 4WD L4-2.3L VIN H HYBRIDREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSRELAYS AND MODULES - COMPUTERS AND CONTROL SYSTEMSENGINE CONTROL MODULESERVICE AND REPAIR
2007 Ford Escape 4WD L4-2.3L VIN H Hybrid
Engine Control Module: Service and Repair
2007 Ford Escape 4WD L4-2.3L VIN H HybridSECTION Service and Repair
POWERTRAIN CONTROL MODULE (PCM)
Removal
1. NOTE: Any PCM replacement will require that ALL customer keys are available to be programmed at the time of installation. PCM replacement DOES NOT require new keys.
Retrieve the module configuration. Carry out the module configuration retrieval steps of the Programmable Module Installation procedure.
2. Remove the nut and the wiring harness retainer from the PCM stud bolt.
3. Remove the nut and the ground strap from the PCM stud bolt.
4. Disconnect the 3 PCM electrical connectors.
5. Remove the 2 stud bolts and the PCM.
Installation
1. Install the PCM and the stud bolts.
- Tighten to 6 Nm (53 lb-in).
2. Connect the 3 PCM electrical connectors.
3. Attach the wiring harness retainer to the PCM stud bolt and install the nut
- Tighten to 6 Nm (53 lb-in).
4. Attach the ground strap to the PCM stud bolt and install the nut.
- Tighten to 6 Nm (53 lb-in).
5. Restore the module configuration. Carry out the module configuration restore steps of the Programmable Module Installation procedure.
6. Reprogram the passive anti-theft system (PATS). Carry out the Parameter Reset procedure.
7. Reprogram the customers keys. Carry out the key programming using the diagnostic equipment procedure.
Removal
1. NOTE: Any PCM replacement will require that ALL customer keys are available to be programmed at the time of installation. PCM replacement DOES NOT require new keys.
Retrieve the module configuration. Carry out the module configuration retrieval steps of the Programmable Module Installation procedure.
2. Remove the nut and the wiring harness retainer from the PCM stud bolt.
3. Remove the nut and the ground strap from the PCM stud bolt.
4. Disconnect the 3 PCM electrical connectors.
5. Remove the 2 stud bolts and the PCM.
Installation
1. Install the PCM and the stud bolts.
- Tighten to 6 Nm (53 lb-in).
2. Connect the 3 PCM electrical connectors.
3. Attach the wiring harness retainer to the PCM stud bolt and install the nut
- Tighten to 6 Nm (53 lb-in).
4. Attach the ground strap to the PCM stud bolt and install the nut.
- Tighten to 6 Nm (53 lb-in).
5. Restore the module configuration. Carry out the module configuration restore steps of the Programmable Module Installation procedure.
6. Reprogram the passive anti-theft system (PATS). Carry out the Parameter Reset procedure.
7. Reprogram the customers keys. Carry out the key programming using the diagnostic equipment procedure.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.