Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007ESCAPE 4WD L4-2.3L VIN H HYBRIDREPAIR AND DIAGNOSISBODY AND FRAMELOCKSKEYLESS ENTRYKEYLESS ENTRY TRANSMITTERTESTING AND INSPECTIONTRANSMITTER
2007 Ford Escape 4WD L4-2.3L VIN H Hybrid
Transmitter
2007 Ford Escape 4WD L4-2.3L VIN H HybridSECTION Transmitter
REMOTE KEYLESS ENTRY TRANSMITTER PROGRAMMING
CAUTION: All remote keyless entry (RKE) transmitters must be programmed at the same time.
1. The vehicle must be electronically unlocked before entering program mode (via the RKE transmitter or the door lock control switch while the driver door is open).
2. Turn the ignition switch from OFF to RUN 8 times within 10 seconds, with the eighth turn ending in RUN. If the module successfully enters program mode, it locks and then unlocks all doors.
3. Within 20 seconds, press any button on an RKE transmitter; and the doors lock and then unlock to confirm that each remote transmitter is programmed. Repeat this step for each RKE transmitter.
4. If the door locks do not respond for any RKE transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification in the Diagnosis and Testing. Make sure that no more than the maximum number of RKE transmitters are attempted to be programmed. Inspection and Verification
5. Exiting the programming mode is accomplished if one of the following occurs:
- The key transitions to the OFF position.
- Twenty seconds have passed since entering programming mode or since the last RKE transmitter was programmed.
- The maximum number of RKE transmitters are programmed.
CAUTION: All remote keyless entry (RKE) transmitters must be programmed at the same time.
1. The vehicle must be electronically unlocked before entering program mode (via the RKE transmitter or the door lock control switch while the driver door is open).
2. Turn the ignition switch from OFF to RUN 8 times within 10 seconds, with the eighth turn ending in RUN. If the module successfully enters program mode, it locks and then unlocks all doors.
3. Within 20 seconds, press any button on an RKE transmitter; and the doors lock and then unlock to confirm that each remote transmitter is programmed. Repeat this step for each RKE transmitter.
4. If the door locks do not respond for any RKE transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification in the Diagnosis and Testing. Make sure that no more than the maximum number of RKE transmitters are attempted to be programmed. Inspection and Verification
5. Exiting the programming mode is accomplished if one of the following occurs:
- The key transitions to the OFF position.
- Twenty seconds have passed since entering programming mode or since the last RKE transmitter was programmed.
- The maximum number of RKE transmitters are programmed.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.