Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2007CROWN VICTORIA LX, 4.6 WREPAIR AND DIAGNOSISENGINE MECHANICALMECHANICALENGINE SYSTEMSPECIFICATIONSTORQUE SPECIFICATIONS
2007 Ford Crown Victoria LX, 4.6 W
Torque Specifications
2007 Ford Crown Victoria LX, 4.6 WSECTION Torque Specifications
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C compressor stud bolts | 25 | 18 | - |
| Accessory drive idler pulley bolt | 25 | 18 | - |
| Camshaft bearing cap boltsa | - | - | - |
| Camshaft sprocket bolta | - | - | - |
| Catalytic converter-to-exhaust manifold nut | 48 | 35 | - |
| Connecting rod bearing cap boltsa | - | - | - |
| Crankshaft main bearing cap boltsa | - | - | - |
| Crankshaft pulley bolta | - | - | - |
| Crankshaft rear seal retainer platea | - | - | - |
| Cylinder head bolta | - | - | - |
| Coolant bypass tube stud bolt | 25 | 18 | - |
| Coolant pump bolts | 25 | 18 | - |
| Coolant pump pulley bolts | 25 | 18 | - |
| Coolant outlet adapter bolts | 25 | 18 | - |
| Engine block coolant drain plug | 20 | 15 | - |
| Engine front covera | - | - | - |
| Engine mount bolts | 70 | 52 | - |
| Engine mount nuts | 90 | 66 | - |
| Engine oil pressure (EOP) switcha | - | - | - |
| EGR tube | 40 | 30 | - |
| Exhaust manifold heat shield bolts | 10 | - | 89 |
| Exhaust manifold nuta | - | - | - |
| Exhaust manifold studs | 12 | 9 | - |
| Flexplate boltsa | - | - | - |
| Generator battery cable nut | 9 | - | 80 |
| Generator bolts | 25 | 18 | - |
| Generator bracket bolts | 10 | - | 89 |
| Ground strap nut | 10 | - | 89 |
| Ground strap-to-RH cylinder head stud bolt | 25 | 18 | - |
| Ground wire-to-fender bolt | 10 | - | 89 |
| Heated oxygen sensor (HO2S) | 40 | 30 | - |
| Ignition coil bolts | 10 | - | 89 |
| Intake manifold boltsa | - | - | - |
| Intake manifold crash bracket bolt | 25 | 18 | - |
| Intake manifold shield bolts | 12 | 9 | - |
| Intermediate steering shaft pinch bolt | 30 | 22 | - |
| Jack screwsa | - | - | - |
| Knock sensor (KS) bolts | 25 | 18 | - |
| Oil cooler hose bolt | 10 | - | 89 |
| Oil filter adapter boltsa | - | - | - |
| Oil level indicator tube bolt | 10 | - | 89 |
| Oil pan boltsa | - | - | - |
| Oil pan drain plug | 13 | 10 | - |
| Oil pump boltsa | - | - | - |
| Oil pump screen cover and pickup tube bolts | 10 | - | 89 |
| Oil pump screen cover and pickup tube spacer | 25 | 18 | - |
| Oil pump screen cover and tube-to-oil pump screen cover and tube spacer bolt | 25 | 18 | - |
| Power steering pump bolts | 25 | 18 | - |
| Power steering tube bracket nut | 10 | - | 89 |
| Shield bolts | 25 | 18 | - |
| Spark plugs | 15 | 11 | - |
| Starter motor boltsa | - | - | - |
| Starter motor B-terminal nut | 12 | 9 | - |
| Starter motor S-terminal nut | 6 | - | 53 |
| Timing chain guide bolts | 10 | - | 89 |
| Timing chain tensioner bolts | 25 | 18 | - |
| Torque converter inspection cover bolts | 19 | 14 | - |
| Torque converter nuts | 36 | 27 | - |
| Transmission bellhousing bolts | 48 | 35 | - |
| Transmission cooler tube bracket bolt | 15 | 11 | - |
| Transmission cooler tube bracket nut | 9 | - | 80 |
| Transmission mount insulator nuts | 30 | 22 | - |
| Transmission wiring harness bracket (located at the rear of RH cylinder head) bolt and stud | 25 | 18 | - |
| Valve cover studs and boltsa | - | - | - |
a Refer to the procedure.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.