DEM Diagnostic Trouble Code (DTC) Index

2005 Ford Taurus SEL, 4D SedanSECTION DEM Diagnostic Trouble Code (DTC) Index
WARNING: This page is about a different car, the 2005 Mercury Montego, 2005 Ford Freestyle, and 2005 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.

DEM Diagnostic Trouble Code (DTC) IndexΒ 

DEM DIAGNOSTIC TROUBLE CODE (DTC) INDEX

DTC Description Source Action
P0562 System Voltage Low DEM REFER to CHARGING SYSTEM - GENERAL INFORMATION .
P0563 System Voltage High DEM REFER to CHARGING SYSTEM - GENERAL INFORMATION .
P0602 Powertrain Control Module Programming Error DEM CLEAR DTCs. REPEAT the self-test. If DTC P0602 is retrieved, INSTALL a new DEM. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTCs. REPEAT the self-test.
P0606 ECU Short to Ground or Open Circuit DEM CLEAR DTCs. REPEAT the self-test. If DTC P0606 is retrieved, INSTALL a new DEM. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTCs. REPEAT the self-test.
P0932 Hydraulic Pressure Sensor Circuit DEM INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test.
P0937 Hydraulic Oil Temperature Sensor Circuit DEM INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test.
P0939 Hydraulic Oil Temperature Sensor Circuit Low Input DEM INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test.
P0940 Hydraulic Oil Temperature Sensor Circuit High Input DEM INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test.
P0960 Pressure Control Solenoid A Control Circuit Open DEM CHECK for damaged rear half-shafts, inner or outer CV joints. MONITOR the ABS wheel speed sensor PIDS to verify that the ABS module is transmitting the correct wheel speeds to the DEM. CHECK for fluid leaks in the active on-demand coupler. REPAIR as necessary. REFER to REAR DRIVE AXLE/DIFFERENTIAL . If no faults are found, INSTALL a new DEM. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTCs. REPEAT the self-test.
P0961 Pressure Control Solenoid A Control Circuit Range Performance DEM CHECK for damaged rear half-shafts, inner or outer CV joints. MONITOR the ABS wheel speed sensor PIDS to verify that the ABS module is transmitting the correct wheel speeds to the DEM. CHECK for fluid leaks in the active on-demand coupler. REPAIR as necessary. REFER to REAR DRIVE AXLE/DIFFERENTIAL . If no faults are found, INSTALL a new DEM. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTCs. REPEAT the self-test.
P0962 Pressure Control Solenoid A Control Circuit Low DEM CHECK for damaged rear half-shafts, inner or outer CV joints. MONITOR the ABS wheel speed sensor PIDS to verify that the ABS module is transmitting the correct wheel speeds to the DEM. CHECK for fluid leaks in the active on-demand coupler. REPAIR as necessary. REFER to REAR DRIVE AXLE/DIFFERENTIAL . If no faults are found, INSTALL a new DEM. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTCs. REPEAT the self-test.
P1889 Oil Pressure Pump Performance DEM INSTALL a new Active On-Demand Coupling Oil Pump. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test. If DTC P1889 is still present, INSTALL the DEM kit (4C016) including all of the parts. REFER to REAR DRIVE AXLE/DIFFERENTIAL . CLEAR the DTCs. REPEAT the self test.
U0001 High Speed CAN Communication Bus DEM REFER to MODULE COMMUNICATIONS NETWORK .
U0121 Lost Communication With Anti-Lock Brake System (ABS) Control Module (One or More Wheel Speeds Missing) DEM REFER to MODULE COMMUNICATIONS NETWORK .
U2050 No Valid Application Added DEM RECONFIGURE the DEM using As-Built Data.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.