4.0L Ranger

2005 Ford Taurus SEL, 4D SedanSECTION 4.0L Ranger
WARNING: This page does not describe the selected car, but rather 29 other vehicles, including the 2011 Mercury Milan, 2011 Mercury Mariner, 2011 Lincoln Navigator L, 2011 Lincoln Navigator, and 2011 Lincoln MKZ. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: 170 Pin PCM Harness Connectors - 4.0L Ranger
G06054079Courtesy of FORD MOTOR CO.

Typical Diagnostic Reference Values 

SENSORS - 4.0L RANGER

Sensors/Inputs PCM Pin/PID only Measured/PID Values Units Measured/PID
KOEO Hot Idle 48 KM/H (30 MPH) 89 KM/H (55 MPH)
FTP B3 2.6/0 2.6/0 2.6/0 2.6/0 VOLTS/PSI
FTP_H2O B3 0 0 0 0 in-H2 O
BOO B8 OFF OFF OFF OFF ON/OFF
FPM B21 OFF ON ON ON ON/OFF
TCS B29 NOT DEPRESSED NOT DEPRESSED NOT DEPRESSED NOT DEPRESSED DEPRESSED/NOT DEPRESSED
CPP/PNP B33 NEUTRAL NEUTRAL DRIVE DRIVE NEUTRAL/DRIVE
ECT E18 0.4-1/93.3-71.1 (200-160) 0.4-1/93.3-71.1 (200-160) 0.4-1/93.3-71.1 (200-160) 0.4-1/93.3-71.1 (200-160) VOLTS/DEG C (DEG F)
DPFEGR E21 0.25-1.30 0.25-1.30 0.25-4.65 0.25-4.65 VOLTS
IAT E22 1.7-3.5/48.8-10 (120-50) 1.7-3.5/48.8-10 (120-50) 1.7-3.5/48.8-10 (120-50) 1.7-3.5/48.8-10 (120-50) VOLTS/DEG C (DEG F)
MAF E25 0 0.7-0.9 1.2-1.6 1.6-2.1 VOLTS
O2S11 E28 (I) switching (C) switching (C) switching (C) VOLTS/RICH-LEAN
O2S21 E29 (I) switching (C) switching (C) switching (C) VOLTS/RICH-LEAN
KNOCK 1 E49 16380 196 173 212 N/A
TP E61 1.05/CT 1.05/CT 1.21/PT 1.29/PT VOLTS/CT/PT/WOT
OSS T3 0 0 1261 2294 RPM
TSS T15 0 775 926 1716 RPM
TR2 T17 CLOSED CLOSED OPEN OPEN OPEN/CLOSED
O2S12 T24 (I) (D) (D) (D) VOLTS
O2S22 T25 (I) (D) (D) (D) VOLTS
TFT T29 0.5-2/98.8-43.3 (210-110) 0.5-2/98.8-43.3 (210-110) 0.5-2/98.8-43.3 (210-110) 0.5-2/98.8-43.3 (210-110) VOLTS/DEG C (DEG F)
ACCS PID OFF ON (A) OFF OFF ON/OFF
B+ PID VBAT VBAT VBAT VBAT VOLTS
BARO PID 14.18/155.1 14.18/155.1 14.18/155.1 14.18/155.1 PSI/Hz
DECHOKE PID YES NO NO NO YES/NO
FCIL PID OFF OFF OFF OFF ON/OFF
FLI PID 50 (H) 50 (H) 50 (H) 50 (H) %
GEAR PID 1 1 4 5 GEAR
LOAD PID (I) 17-28 19-26 30-40 %
O2BANK1 PID VARIES VARIES VARIES VARIES RICH/LEAN
O2BANK2 PID VARIES VARIES VARIES VARIES RICH/LEAN
RPM PID 0 750 1300-1350 1780 RPM
TORQUE PID 238.7 10.85 8.13 179 Nm
TPCT PID 1.05 1.05 1.05 1.05 VOLTS
TR PID P P OD OD MODE
TSS/ISS PID 0 750 990 1720 RPM
VSS PID 0 0 48 km/h (30 MPH) 89 km/h (55 MPH) km/h/MPH
ACTUATORS - 4.0L RANGER

Actuators/Outputs PCM Pin/PID only Measured/PID Values Units Measured/PID
KOEO Hot Idle 48 KM/H (30 MPH) 89 KM/H (55 MPH)
FP B12 OFF ON ON ON ON/OFF
PCVHC E3 0 0 0 0 %
EVMV E6 0 0 500-900 (F) 500-900 (F) mA
IAC E33 0 35 35-41 (I) 57-68 (I) %
EGRVR E63 0 0 VARIES VARIES %
HTR11 E69 OFF ON ON ON ON/OFF
HTRCM11 E69 539 539 535 535 mA
HTR21 E70 OFF ON ON ON ON/OFF
HTRCM21 E70 504 504 500 500 mA
TCC T46 0/OFF 0/OFF 0/OFF 100/ENGAGED %/OFF-ENGAGED
HTR12 T47 OFF ON ON ON ON/OFF
HTRCM12 T47 938 938 906 906 mA
HTR22 T48 OFF ON ON ON ON/OFF
HTRCM22 T48 922 922 945 945 mA
EGR_EVAL PID NO NO NO NO YES/NO
EVAP020C PID NO NO NO NO YES/NO
EVAP020D PID ALLOW ALLOW ALLOW ALLOW ALLOW/DISALLOW
EVAP020R PID NOT READY NOT READY NOT READY NOT READY READY/NOT READY
EVAPCV PID 0/OFF 0/OFF 0/OFF 0/OFF %/ON/OFF
EVAPSOAK PID YES YES NO NO YES/NO
EVAP_EVAL PID NO NO NO NO YES/NO
FUELSYS PID OPEN LOOP CLOSED LOOP CLOSED LOOP CLOSED LOOP OPEN/CLOSED LOOP
LONGFT1 PID (I) -20 TO +20 -20 TO +20 -20 TO +20 %
LONGFT2 PID (I) -20 TO +20 -20 TO +20 -20 TO +20 %
MIL PID OFF OFF OFF OFF ON/OFF
SHRTFT1 PID 0 -10 TO +10 -10 TO +10 -10 TO +10 %
SHRTFT2 PID 0 -10 TO +10 -10 TO +10 -10 TO +10 %
SPARKADV PID 0 20-25 30-35 30-35 DEG
OTHERS - 4.0L RANGER

Other PCM Pin/PID only Measured/PID Values Units Measured/PID
KOEO Hot Idle 48 KM/H (30 MPH) 89 KM/H (55 MPH)
VPWR B35/B36 VBAT VBAT VBAT VBAT VOLTS
VREF B40/T40 5 5 5 5 VOLTS
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.