Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2.5L 4V Fusion/Milan
2005 Ford Taurus SEL, 4D SedanSECTION 2.5L 4V Fusion/Milan
WARNING: This page does not describe the selected car, but rather 29 other vehicles, including the 2011 Mercury Milan, 2011 Mercury Mariner, 2011 Lincoln Navigator L, 2011 Lincoln Navigator, and 2011 Lincoln MKZ. However, it is still accessible from the selected car via links, so may be relevant.
Typical Diagnostic Reference Values
SENSORS - 2.5L 4V FUSION/MILAN
| Sensors/Inputs | PCM Pin/PID only | Measured/PID Values | Units Measured/PID | |||
|---|---|---|---|---|---|---|
| KOEO | Hot Idle | 48 KM/H (30 MPH) | 89 KM/H (55 MPH) | |||
| BOO1 | B13 | OFF | ON (E) | OFF | OFF | ON/OFF |
| APP1 | B28 | 0.77 | 0.77 | 0.93 | 0.77 | VOLTS |
| APP2 | B29 | 0.38 | 0.38 | 0.47 | 0.39 | VOLTS |
| FPM | B32 | 60.35 | 60.35 | 60.35 | 59.71 | % |
| MAF (A/T) | B40 | 0.01 | 0.73 | 1.77 | 1.66 | VOLTS |
| MAF (M/T) | B40 | 0.01 | 0.41 | 0.73 | 1.97 | VOLTS |
| BOO2 | B46 | OFF | ON (E) | OFF | OFF | ON/OFF |
| IAT | B47 | 2.11/42 (107.6) | 2.36/37 (98.6) | 3.16/21 (69.8) | 3.58/13 (55.4) | VOLTS/DEG C (DEG F) |
| FTP | B65 | 2.6/0 | 2.56/0 | 2.29/0 | 2.17/-0.11 | VOLTS/PSI |
| FTP_H2O | B65 | 0.13 | -0.44 | -2.34 | -3.2 | in-H2 O |
| O2S11 | E8 | (I) | switching (C) | switching (C) | switching (C) | VOLTS |
| CHT | E39 | 0.54/94 (201.2) | 0.6/90 (194) | 3.81/88 (190.4) | 3.52/97 (206.6) | VOLTS/DEG C (DEG F) |
| MAP | E40 | 4/98.93/14.3/29.11 | 1.2/27.99/4.06/8.26 | 2.25/53.98/7.83/15.94 | 2.13/51.98/7.54/15.35 | VOLTS/kPa/PSI/inHg |
| TP1 | E41 | 4.1 | 4.34 | 4.16 | 4.2 | VOLTS |
| KNOCK_1 | E43 | 288 | 216 | 221 | 227 | N/A |
| TP2 | E58 | 1.19 | 0.71 | 1.08 | 1.15 | VOLTS |
| HTRCM11 | E69 | 0 | 0 | 0 | 1.41 | Amps |
| TSS_SRC (A/T) | T16 | 0 | 716.5 | 1235.25 | 1708.5 | RPM |
| TFT (A/T) | T19 | 46 (114.8) | 44 (111.2) | 80 (176) | 89 (192.2) | DEG C (DEG F) |
| TFTV (A/T) | T19 | 1.99 | 2.04 | 0.8 | 0.64 | VOLTS |
| OSS_SRC (A/T) | T25 | 0 | 0 | 1153 | 2290 | RPM |
| CPP_BOT (M/T) | T26 | NO | NO | NO | NO | YES/NO |
| CPP_TOP (M/T) | T27 | NO | NO | NO | NO | YES/NO |
| O2S12 | T29 | (I) | (D) | (D) | (D) | VOLTS |
| HTRCM12 | T49 | 0 | 0 | 0 | 571 | mA |
| APP | PID | 0 | 0 | 5 | 0 | % |
| BARO | PID | 14.35/156.1 | 14.35/156.1 | 14.35/156.1 | 14.21/155.2 | PSI/Hz |
| B+ | PID | 12.47 | 13-14 | 13-14 | 13-14 | VOLTS |
| DECHOKE | PID | NO | NO | NO | NO | YES/NO |
| ETC_ACT | PID | 8.04 | 1.54 | 4.7 | 9.89 | DEG |
| ETC_DSD | PID | 7.62 | 1.57 | 4.71 | 9.81 | DEG |
| ETC_TRIM | PID | 0.13 (J) | 0.15 (J) | 0.14 (J) | 0.07 (J) | DEG |
| FLI | PID | 50 (H) | 50 (H) | 50 (H) | 50 (H) | % |
| GEAR (A/T) | PID | 1 | 1 | 5 | 6 | GEAR |
| LOAD (A/T) | PID | 0(I) | 20.78 | 30.98 | 54.51 | % |
| LOAD (M/T) | PID | 0(I) | 22.74 | 54.51 | 46.66 | % |
| MISFIRE | PID | NO | NO | NO | NO | YES/NO |
| MP_LRN | PID | YES | YES | YES | YES | YES/NO |
| O2BANK1 | PID | VARIES | VARIES | VARIES | VARIES | RICH/LEAN |
| RPM | PID | 0 | 754.75 | 1659 | 1708.75 | RPM |
| SYNC | PID | NO | YES | YES | YES | YES/NO |
| VCT1_F | PID | NO FAULT | NO FAULT | NO FAULT | NO FAULT | FAULT/NO FAULT |
| VSS | PID | 0 | 0 | 48 km/h (30 MPH) | 89 km/h (55 MPH) | km/h/MPH |
ACTUATORS - 2.5L 4V FUSION/MILAN
| Actuators/Outputs | PCM Pin/PID only | Measured/PID Values | Units Measured/PID | |||
|---|---|---|---|---|---|---|
| KOEO | Hot Idle | 48 KM/H (30 MPH) | 89 KM/H (55 MPH) | |||
| FP | B19 | 75/OFF | 40.04/ON | 41.2/ON | 40.92/ON | %/ON/OFF |
| EVAPCV | B20 | 0/OFF | 0/OFF | 0/OFF | 0/OFF | %/ON/OFF |
| EVAPCP | E32 | 0 | 41.56 | 72.94 | 79.6 | % |
| VCTDC | E67 | 0 | 0 | 0 | 0 | % |
| HTR11 | E69 | OFF | ON | ON | ON | ON/OFF |
| HTR12 | T49 | OFF | ON | ON | ON | ON/OFF |
| CAT_EVAL | PID | YES | YES | YES | YES | YES/NO |
| EGR_EVAL | PID | YES | YES | YES | YES | YES/NO |
| EVAP020C | PID | NO | NO | NO | NO | YES/NO |
| EVAPSOAK | PID | YES | YES | YES | YES | YES/NO |
| EVAP_EVAL | PID | NO | NO | NO | YES | YES/NO |
| FUELSYS | PID | OPEN LOOP | CLOSED LOOP | CLOSED LOOP | CLOSED LOOP | OPEN/CLOSED LOOP |
| HFC | PID | OFF | ON (B) | OFF | OFF | ON/OFF |
| LFC | PID | OFF | ON (B) | OFF | OFF | ON/OFF |
| LONGFT1 | PID | -20 TO +20 | -20 TO +20 | -20 TO +20 | -20 TO +20 | % |
| MIL | PID | OFF | OFF | OFF | OFF | ON/OFF |
| PATSENABL | PID | ENABLED | ENABLED | ENABLED | ENABLED | ENABLED/DISABLED |
| RPMDSD | PID | 750 | 750 | 650 | 650 | RPM |
| SHRTFT1 | PID | (I) | -10 TO +10 | -10 TO +10 | -10 TO +10 | % |
| SPARKADV (A/T) | PID | 12.25 | 14-20 | 35-44 | 30-40 | DEG |
| SPARKADV (M/T) | PID | 10 | 14.25 | 45.25 | 53 | DEG |
| STRT_RLY | PID | DISABLED | DISABLED | DISABLED | DISABLED | ENABLED/DISABLED |
| TCC (A/T) | PID | 0 | 0 | 25.52 | 41.18 | PSI |
| TCIL | PID | OFF | OFF | OFF | OFF | ON/OFF |
| TQ_CNTRL | PID | NONE | NONE | NONE | NONE | _ |
| VCTADV | PID | 0 | -0.25 | -0.25 | 0.25 | DEG |
| VCTADVERR | PID | 0 | 0.25 | 0.25 | -0.25 | DEG |
| VCT_DSD | PID | 0 | 0 | 0 | 0 | DEG |
| VCTSYS | PID | OPEN LOOP | CLOSED LOOP | CLOSED LOOP | CLOSED LOOP | OPEN/CLOSED LOOP |
OTHERS - 2.5L 4V FUSION/MILAN
| Other | PCM Pin/PID only | Measured/PID Values | Units Measured/PID | |||
|---|---|---|---|---|---|---|
| KOEO | Hot Idle | 48 KM/H (30 MPH) | 89 KM/H (55 MPH) | |||
| VREF | B52/E35 | 5 | 5 | 5 | 5 | VOLTS |
| VPWR | B67/68 | 12.39 | 13-14 | 13-14 | 13-14 | VOLTS |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.