Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2005ECONOLINE E150, VAN CARGO, 5.4 LREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXANTI-LOCK CONTROL DTCS
2005 Ford Econoline E150, Van Cargo, 5.4 L
Anti-Lock Control DTCS
2005 Ford Econoline E150, Van Cargo, 5.4 LSECTION Anti-Lock Control DTCS
ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTCS | Description | Perform Test |
|---|---|---|
| B1342 | ABS Module Internal Failure | INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . |
| B1676 | Battery Voltage Out of Range | GO to PINPOINT TEST J . |
| C1095/C1096 | Anti-Lock Brake System (ABS) Hydraulic Pump Motor Circuit Failure | GO to PINPOINT TEST I . |
| C1145 | RF Wheel Speed Sensor Input Circuit Failure | GO to PINPOINT TEST B . |
| C1148 | RF Wheel Speed Sensor Coherency Fault | GO to PINPOINT TEST D . |
| C1155 | LF Wheel Speed Sensor Input Circuit Failure | GO to PINPOINT TEST B . |
| C1158 | LF Wheel Speed Sensor Coherency Fault | GO to PINPOINT TEST D . |
| C1169 | Excessive Anti-Lock Brake System (ABS) Fluid Dump Time | REPAIR all other DTCs, GO to PINPOINT TEST E . |
| C1184 | Anti-Lock Brake System (ABS) Time Out | GO to PINPOINT TEST H . |
| C1185 | Anti-Lock Brake System (ABS) | Power Relay Output Circuit Failure GO to PINPOINT TEST F . |
| C1194, C1196, C1198, C1200, C1202, C1204, C1206, C1208, C1210, C1212, C1214 or C1216 | ABS Valve Coil Circuit Failure | INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this section. |
| C1220 | Lamp ABS Warning Output Circuit Short To Battery | REFER to INSTRUMENT CLUSTER to continue diagnosis of the lamp. |
| C1222 | Wheel Speed Mismatch | GO to PINPOINT TEST C . |
| C1225/C1226 | Lamp Brake Warning Output Circuit Failure | REFER to INSTRUMENT CLUSTER to continue diagnosis of the lamp. |
| C1229 | Differential Wheel Speed Sensor Coherency Fault | GO to PINPOINT TEST D . |
| C1230 | Differential Wheel Speed Sensor Input Circuit Failure | GO to PINPOINT TEST B . |
| C1233 | LF Wheel Speed Input Signal Missing | GO to PINPOINT TEST C . |
| C1234 | RF Wheel Speed Input Signal Missing | GO to PINPOINT TEST C . |
| C1237 | Differential Wheel Speed Input Signal Missing | GO to PINPOINT TEST C . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.