Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2004ESCAPE 2.0 BREPAIR AND DIAGNOSISTRANSMISSIONMANUAL TRANSMANUAL TRANSMISSIONSPECIFICATIONSTORQUE SPECIFICATIONS
2004 Ford Escape 2.0 B
Torque Specifications
2004 Ford Escape 2.0 BSECTION Torque Specifications
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Case cover bolts | 10 | - | 89 |
| Clutch fork anchor bolt | 39 | 29 | - |
| Clutch slave cylinder bolts | 20 | 15 | - |
| Clutch slave cylinder line bracket bolts | 20 | 15 | - |
| Differential cover bolts | 164 | 121 | - |
| Differential cover screws | 9 | - | 80 |
| Differential turning torque | 0.5 | - | 4.3 |
| Drain plug | 47 | 35 | - |
| Front to aft crossmember bolts | 90 | 66 | - |
| Front transaxle support insulator bracket bolts | 55 | 41 | - |
| Front transaxle support insulator bolt | 90 | 66 | - |
| Front wire harness bracket nut | 12 | 9 | - |
| Input shaft lock nut | 160 | 118 | - |
| LH transaxle support insulator bracket to transaxle bolt and nuts | 90 | 66 | - |
| LH transaxle support insulator to bracket bolt | 90 | 66 | - |
| LH transaxle support insulator to body bolts | 55 | 41 | - |
| Lock bolt | 18 | 13 | - |
| Output shaft locknut | 160 | 118 | - |
| Park/neutral position (PNP) switch | 25 | 18 | - |
| Rear transaxle support insulator bolt | 90 | 66 | - |
| Rear transaxle support insulator to subframe bolt and nuts | 90 | 66 | - |
| Rear transaxle support insulator bracket to transaxle bolts | 90 | 66 | - |
| Rear wire harness bracket to transaxle bolts | 9 | - | 80 |
| Reversing lamp switch | 25 | 18 | - |
| Reverse idler shaft lock bolt | 22 | 16 | - |
| Shift gate bolt | 13 | 10 | - |
| Shifter linkage nut | 20 | 15 | - |
| Shift rail guide bolt | 12 | 9 | - |
| Shift control selector plate 1 | 10 | - | 89 |
| Shift control selector plate 2 | 28 | 21 | - |
| Shift control shaft selector lever bolt | 13 | 10 | - |
| Stabilizer bar to transaxle bolt | 40 | 30 | - |
| Starter motor bolts | 45 | 33 | - |
| Transaxle case to flywheel housing bolts | 45 | 33 | - |
| Transaxle flywheel housing to engine bolts | 45 | 33 | - |
| Transverse crossmember bolts | 115 | 85 | - |
| Vehicle speed sensor (VSS) bolt | 7 | - | 62 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.