Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2004ECONOLINE E150, VAN CARGO, 4.6 WREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 58 (ENGINE CONTROLS - SELF-DIAGNOSTICS)DIAGNOSTIC TROUBLE CODE DEFINITIONS
2004 Ford Econoline E150, Van Cargo, 4.6 W
Diagnostic Trouble Code Definitions
2004 Ford Econoline E150, Van Cargo, 4.6 WSECTION Diagnostic Trouble Code Definitions
WARNING: This page is about a different car, the 2002 Mercury Villager. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC TROUBLE CODE DEFINITIONS
| DTC | Description | Go To | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| P0000 | No Faults Detected | N/A | ||||||||
| P0100 | MAF Sensor Circuit Fault | Test DC , Step 1) | ||||||||
| P0105 | MAP/BARO Sensor Fault | Test DB , Step 1) | ||||||||
| P0110 | IAT Sensor Circuit Fault | Test DA , Step 1) | ||||||||
| P0115 | ECT Sensor Circuit Fault | Test DA , Step 1) | ||||||||
| P0120 | Throttle Position Sensor Circuit Fault | Test DH , Step 1) | ||||||||
| P0125 | Insufficient Coolant Temperature For Closed Loop | Test DA , Step 100) | ||||||||
| P0130 | HO2S-11 Circuit Malfunction | Test H , Step 1) | ||||||||
| P0131 | HO2S-11 Low Voltage | Test H , Step 1) | ||||||||
| P0132 | HO2S-11 High Voltage | Test H , Step 1) | ||||||||
| P0133 | HO2S-11 Slow Response | Test H , Step 1) | ||||||||
| P0134 | HO2S-11 No Activity Detected | Test H , Step 1) | ||||||||
| P0135 | HO2S-11 Heater Circuit Malfunction | Test H , Step 20) | ||||||||
| P0137 | HO2S-12 Low Voltage | Test H , Step 1) | ||||||||
| P0138 | HO2S-12 High Voltage | Test H , Step 1) | ||||||||
| P0139 | HO2S-12 Slow Response | Test H , Step 1) | ||||||||
| P0140 | HO2S-12 No Activity Detected | Test H , Step 1) | ||||||||
| P0141 | HO2S-12 Heater Circuit Malfunction | Test H , Step 20) | ||||||||
| P0171 | Fuel Mixture Too Lean - Bank 1 | Test H , Step 40) | ||||||||
| P0172 | Fuel Mixture Too Rich - Bank 1 | Test H , Step 40) | ||||||||
| P0180 | Fuel Temperature Sensor Circuit | Test HX , Step 120) | ||||||||
| P0300 | Random Or Multiple Misfire Detected | Test HD , Step 1) | ||||||||
| P0301 | Cylinder No. 1 Misfire Detected | Test HD , Step 1) | ||||||||
| P0302 | Cylinder No. 2 Misfire Detected | Test HD , Step 1) | ||||||||
| P0303 | Cylinder No. 3 Misfire Detected | Test HD , Step 1) | ||||||||
| P0304 | Cylinder No. 4 Misfire Detected | Test HD , Step 1) | ||||||||
| P0305 | Cylinder No. 5 Misfire Detected | Test HD , Step 1) | ||||||||
| P0306 | Cylinder No. 6 Misfire Detected | Test HD , Step 1) | ||||||||
| P0325 (1) | Knock Sensor Circuit Fault | Test DG , Step 1) | ||||||||
| P0335 | CKP Sensor Circuit Fault | Test DS , Step 1) | ||||||||
| P0340 | CMP Sensor Circuit Fault | Test DR , Step 1) | ||||||||
| P0420 | Catalyst Efficiency Fault; Bank 1 | Test HF , Step 1) | ||||||||
| P0440 | Small Leak Detected In Evaporative Emission System | (2) | ||||||||
| P0443 | EVAP Emission Control System Purge Volume Control Valve | Test HX , Step 15) | ||||||||
| P0446 | EVAP Emission Control System Vent Control Circuit | Test HX , Step 35) | ||||||||
| P0450 | EVAP Emission Control System Pressure Sensor Malfunction | Test HX , Step 25) | ||||||||
| P0455 | EVAP Emission Control System Leak Detected (Gross Leak/No Flow) | (2) | ||||||||
| P0500 | Vehicle Speed Sensor Malfunction | Test DP , Step 1) | ||||||||
| P0505 | Idle Control System Fault | Test KE , Step 1) | ||||||||
| P0510 | Closed TP Sensor Malfunction | Test HB , Step 1) | ||||||||
| P0600 | Serial Communication Link Fault | Test QA , Step 30) | ||||||||
| P0605 | PCM Read Only Memory Error | (3) | ||||||||
| P0705 | Transmission Range Sensor Circuit Malfunction | (4) | ||||||||
| P0710 | Transmission Fluid Temperature Sensor Circuit Malfunction | (4) | ||||||||
| P0720 | Output Speed Sensor Circuit Malfunction | (4) | ||||||||
| P0725 | Engine Speed Input Circuit Malfunction | Test ND , Step 10) | ||||||||
| P0731 | Incorrect Ratio - Gear 1 | (4) | ||||||||
| P0732 | Incorrect Ratio - Gear 2 | (4) | ||||||||
| P0733 | Incorrect Ratio - Gear 3 | (4) | ||||||||
| P0734 | Incorrect Ratio - Gear 4 | (4) | ||||||||
| P0740 | Torque Converter Clutch Circuit Malfunction | (4) | ||||||||
| P0744 | Torque Converter Clutch Solenoid Malfunction | (4) | ||||||||
| P0745 | Pressure Control Solenoid Malfunction | (4) | ||||||||
| P0750 | Shift Solenoid "A" Circuit Malfunction | (4) | ||||||||
| P0755 | Shift Solenoid "B" Circuit Malfunction | (4) | ||||||||
| P1105 | MAP/BARO Solenoid Circuit Malfunction | Test DB , Step 15) | ||||||||
| P1148 | Closed Loop Control Malfunction | Test H , Step 1) | ||||||||
| P1217 | Engine Over Temperature | Test DA , Step 19) | ||||||||
| P1320 | Distributor Signal Interrupt | Test JA , Step 3) | ||||||||
| P1336 | Crankshaft Position Sensor | Test DS , Step 1) | ||||||||
| P1440 | EVAP Emission Control System Small Leak Detected | (2) | ||||||||
| P1444 | EVAP Emission Control System Canister Purge Valve | Test HX , Step 20) | ||||||||
| P1446 | EVAP Emission Control System Vent Control (Closed) | Test HX , Step 95) | ||||||||
| P1447 | EVAP Emission Purge Flow Monitoring | Test HX , Step 105) | ||||||||
| P1448 | EVAP Emission Control System Vent Control (Open) | Test HX , Step 85) | ||||||||
| P1490 | EVAP Emission Vacuum Cut By-Pass Solenoid Circuit | Test HX , Step 65) | ||||||||
| P1491 | EVAP Emission Vacuum Cut By-Pass Solenoid Malfunction | Test HX , Step 75) | ||||||||
| P1605 | A/T Data Communication Line Fault | Test QA , Step 30) | ||||||||
| P1705 | Throttle Position Sensor Fault (A/T) | Test KN , Step 1) | ||||||||
| P1706 | Park/Neutral Position Switch Not Switching | (4) | ||||||||
| P1760 | Overrun Clutch S/V | (4) | ||||||||
|
||||||||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.